Search results

  1. A

    Temp sender removal …

    Have used tour idea many times and it does work, but my concern is the fastener is brass and could easily be damaged by a sharp blow, or mashed where it couldn't be removed... if it were steel, I would agree fully.
  2. A

    Temp sender removal …

    Great idea, but from the pic posted, I don't think there is a head left, appears the center is hollow where the heat sensor broke out. But I could be wrong, just looking at the pic.....
  3. A

    Gauges recommendation

    Make sure all connections, splices or any other electrical joints are thoroughly clean and shiny before hooking up new gages. Good luck...
  4. A

    25hp Yamaha Bogging Down

    You swapped the wires between the two cylinders and the motor ran ok in both positions?
  5. A

    Temp sender removal …

    Brass and aluminum do not play well together unless a barrier was added to the threads before install. Worse case scenario is the head might need removed to machine out the left overs. I would try heat then cold a few times to see if the corrosion can be broke loose. Good luck.....
  6. A

    Newbie boat owner

    If you plan on keeping this boat, I would beg, borrow, hunt, search, scour until you find a factory service manual for it. I have found most of mine off ebay, and garage sales, but they are necessary for maintenance specs. Good luck.
  7. A

    Gauges recommendation

    In my years of boat ownership, most issues with gages have been corroded, dirty, loose connections !! Could count on one hand the actual number of "faulty" gages. Damaged and broken gages yes, but worn out or faulty was rare. If you want newer or better looking gages, then fine....but be...
  8. A

    1957 Johnson Seahorse 35hp value?

    Fewer folks are capable of repairing nowadays, we have become or are turning into a throw away society. With high labor costs and reduced manufacturing costs by not designing items for repair, the cost and effort to repair is to costly. While making repairs before selling may not be...
  9. A

    1957 Johnson Seahorse 35hp value?

    Lake Erie, we have the largest walleye population of catchable walleye than any other place on earth.
  10. A

    1957 Johnson Seahorse 35hp value?

    Our local repair shop guy stated that folks really like there four strokes, but fear repair costs if anything goes haywire. Maintenance us much higher and most that buy new also buy extended warranties out to ten years. Many are beginning to look at trading in there almost 10 year old motors...
  11. A

    Good enough RPM or not (92' Yamaha 130 v4 2 stroke)

    Every inch in n pitch changes engine rpm by 200 rpm, every inch in diameter changes rpm by 100 rpm. Those are the general rules of thumb. Use your current prop at wot, and adjust accordingly.
  12. A

    Looking for my first boat and dwelling too much on the I/O vs Outboard question...

    According to my local coast card officer, the mfgr is required to have enough flotation to maintain level flotation ( not sink to the bottom) on all boats under 26' in length. In today's law suit market, mfgrs will do what ever they can to not get sued. My neighbors 29' fiberglass is full of...
  13. A

    Pressed-in Zerk grease fittings

    People don't clean off the fitting before pumping in the grease. Crud on the zerk gets forced in with the grease and often builds up. Not common but does happen, wipe clean the fitting and be sure the nipple on the grease gun is clean before pumping in grease. I normally give a little pump on...
  14. A

    3L cobra idling too high

    Setting idle speed should be done in the water while underway for best results.
  15. A

    Mercruiser 350 MAG MPI missing only at 3000 rpms

    If four stroke, looks about right, but if from a two stroke it looks slightly lean. Opps, never mind, just realized this was under the Mercruiser section...
  16. A

    Need help with ID of what's left of an 18' alum boat.

    My guess would be Lone Star as well....but just a guess as they were noted for short front decks.
  17. A

    My boat needs to run real good on the 4th of July. FIX IT !!

    Here on make erie, there is enough room that we are not packed that tight, however....the long lines waiting at the launch ramps is another story !! Those that do not know how to backup, nor actually how to load their boats all stand out like a sore thumb ! Many that keep their boats moored are...
  18. A

    tahoe 1950 trailer guide pole

    Not ever living in a tide area, that was never in my thoughts..
  19. A

    1957 Johnson Seahorse 35hp value?

    Today, no one wants a fixer upper, it needs to run and run well in order to get top dollar. Finding service depends on where you live. Here in the walleye capital, find folks to work on older two strokes is easy and plentifull, not cheap, but plenty of these motor still around. What has been...
  20. A

    1957 Johnson Seahorse 35hp value?

    When it comes to older used motors, smaller up often brings bigger $$. Small engines are used as kicker ( spare/trolling) use or on small boats staying close to shore.
Top