Search results

  1. The Force power

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    IF the inner parts are good, a piece missing out of the Skeg would not de-value the lower-unit (here in Ontario, Canada it would sell $200-250)
  2. The Force power

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    This is matter of opinion(s) there's equal amount that would state the opposite Finding parts can be a daunting task(not impossible/cheap) but neither is the boat you're working on Looks like the pistons are still in the block, the cylinder-wall would need to be inspected for scores They are...
  3. The Force power

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    This is a '89 Force IF the electronics are good and the Cylinder-wall(s) not too badly scored; it would be a great motor to repair. I've done a few (6) of them & own four of them
  4. The Force power

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    No guessing required; that is the trailering support bracket for the Force engine. While the engine is trimmed up this bracket slides in the holes from the transom-brackets & kept in place with a cotter-pin through one of the ends I lost mine once at the boat launch & retrieved at the end of the...
  5. The Force power

    1984 125 force outboard

    The cowl is the cover on the outboard engine
  6. The Force power

    1999 Force/Merc 75HP 3 Cylinder 2-Stoke Rough Running Issues

    I found "part number 632061" in about 20 seconds on fleabay (not sure if that is the correct one) Can yours not just be cleaned?
  7. The Force power

    1984 125 force outboard

    Lets call a spade a spade, what is for you "the console" ?? you mean; under the cowl ? (engine side) OR the controls in the boat ?
  8. The Force power

    1984 125 force outboard

    Is the lower-unit also in neutral? (with shift-shaft connected / prop spinning freely) IF yes to both; adjust the cable at the controls ( remove cable at shifter & attached in the appropriate mounting-hole Sorry, I have to ask; do you have the correct cable hooked to the correct point ?(its...
  9. The Force power

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    :D :D where are the donuts & coffee
  10. The Force power

    Hybrid Vehicles

    Only if there money to be made
  11. The Force power

    Hybrid Vehicles

    No need for those led strip-light anymore; the car will glow on its own :D
  12. The Force power

    1984 125 force outboard

    When your shifter (in the boat) AND the timing-tower is neutral (starter interrupt-switch De-activated) The upper shift-shaft (lever) should be budding-up against each other see circulated area. When everything is properly adjusted.......this allows the advance throttle to only go so far (in...
  13. The Force power

    1984 125 force outboard

    IF in the upper pic. the shifter & also the lower-unit are also in neutral?? then you'll have to adjust the upper shift-shaft because its not flush (see pic.)
  14. The Force power

    Grandpa's ole Chrysler

    You brought back an old memory & ensured new memories can be made for next generations, hands down great job!
  15. The Force power

    Looking for some help

    Maybe chunks of fuel-line, have you checked the screen in the pump? I would install an inline fuel filter between the pump & Carburetors
  16. The Force power

    Looking for some help

    0.10 = .254 mm
  17. The Force power

    Looking for some help

    Corrected
  18. The Force power

    Looking for some help

    The service manual says; 0.10 (.255mm) maximum opening ALLOWED Like Nordin asked; are all the pedals having this gap? & check with a flashlight how many? If the motor is running with "bad" valve reeds it would be spitting fuel out the carb's throat Do not flip the pedal reeds around! there will...
  19. The Force power

    Looking for some help

    If #1 is at TDC and the mark on the flywheel lines up, the key is good
  20. The Force power

    Looking for some help

    What procedure did he use?
Top