Search results

  1. 9

    2005 Yamaha 115 losing fuel pressure

    lack of fuel will not prevent the starter from turning the motor over you said the motor runs fine until you shut it down and let it cool off. pump the bulb before trying to start it up again. and how can you pump the bulb if the bulb is flat/
  2. 9

    2005 Yamaha 115 losing fuel pressure

    so apparently you have not tried pumping the primer bulb before restarting to see if that helps. try it and get back to us. also if the bulb is being sucked flat, you have a restriction
  3. 9

    2005 Yamaha 115 losing fuel pressure

    have you tried pumping the primer bulb before restarting the motor to see if that keeps it from happening? Does this motor have a fuel cooler? if it does is it working properly?
  4. 9

    Z150TRXA

    I forgot about that small oil pump to the VST. no idea what and when it runs by the way I was talking about fuel pumps before
  5. 9

    Z150TRXA

    maybe you are thinking oil level low not oil pump low.. sounds like the lift pump is not keeping the VST full at low RPM. restriction or sucking air that pump may not run all of the time at low RPM
  6. 9

    1998 Yamaha F50 fuel enrichtment system how does it work?

    is there voltage to that heater unit while the motor is running?
  7. 9

    Gas leak from lower unit

    there should be no fuel in the lower unit, so why should it be leaking from it
  8. 9

    94 15 yammy

    that looks too dark to be fresh/clean lower unit lube. what does it smell like? lower unit lube stinks so you will be able to tell if it is that does water normally come out of that hole while running on the muffs? if so that is just a drain hole so water does not sit in that area. is this...
  9. 9

    Water in lower? Yamaha 4

    that 1st pic looks like a lot of water flowing out around the lower unit. I am not familiar with those small outboards, are you sure you have the tube shoved down into the water pump seal properly? maybe it moved as you put the lower unit on
  10. 9

    1998 Yamaha F50 fuel enrichtment system how does it work?

    if the choke plates do not open up as the should, you could see that if you looked. I have no idea how that system works since I never looked at a motor like it or a manual for it
  11. 9

    1998 Yamaha F50 fuel enrichtment system how does it work?

    Robert, this system he has is no where close to what you and I have on our motors. he needs to read up on what Boscoe sent him
  12. 9

    Where to install temp sensor on Yamaha 175 v-max

    what are you calling the zone
  13. 9

    Carb Roller Part # for Yamaha 25ESD

    well that looks to me like they are talking about just 9.9 motors. no wait a minute it does not. hard to believe most 2 strokes would have the same part how do you remove the roller and put the new one on?
  14. 9

    1990 Yamaha 250 VX 76. Power drops off.

    well what all does this stator do lighting coil furnishes voltage/current for battery charge coil furnishes voltage to CDI Pulser coils tell CDI when to fire spark plugs Edit: apparently all are set in one piece on this old motor
  15. 9

    Prop caught on trap, engine wont turn over

    1st thing to do would be pull the prop off and make sure nothing is binding up between the prop and gear case
  16. 9

    Prop caught on trap, engine wont turn over

    does the starter engage but not turn the motor? or is the starter not even tying to energize? some 4 stroke motors have the oil pump run off of the drive shaft, so if that is not in place then there is no oil being pumped It is always a good idea to state the complete model # of the motor you...
  17. 9

    Yamaha 4hp 2 Stroke Powerhead Removal

    follow the path of the TT to see where it goes into the powerhead, and disconnect the hose from there, to clean it out better in both directions. I am guessing there is a hose making the connection between the two.
  18. 9

    Yamaha 4hp 2 Stroke Powerhead Removal

    No help on pulling power head, but did you try hooking a water hose to the water pipe heading up to power head from water pump, turning on the water to see if water flows out the tell tale then? what about removing the stat cover to see if water comes out of there? If water flows that way...
  19. 9

    Carburetor question on restoration I’m working on 1992 40 hp MSHQ Yamaha

    Faz was only giving reasons for clean plugs but then people play with jetting all the time changing things and some jets/passages can get partially restricted. someone saying the carbs are clean does not always mean that is true
  20. 9

    2004 Yamaha Z200TXRC hdpi - Fuel in Exhaust

    knowing if rail pressure is in spec would be a good idea
Top