Search results

  1. alldodge

    I was just four months old

    All the statements that cover everyone but do not consider requirements to do so. You have to be close enough to the transmission antenna to be able to get for free
  2. alldodge

    6.2L MX MPI Stalls when shifting out of gear

    No the 2 bolts holding the other piece
  3. alldodge

    6.2L MX MPI Stalls when shifting out of gear

    There are 2 bolts holding the plate, one of them allows it to pivot You are shifting quickly, right not slow?
  4. alldodge

    6.2L MX MPI Stalls when shifting out of gear

    Adjust the shift interrupter switch first, and if that doesn't work you probably need a new switch
  5. alldodge

    WOT RPM Low. MAG350 MPI B3

    The fuel module did not pass step 4, correct? It did not pass step 4 is the reason to go to step 5 35 psi fuel pressure and 13 in Hg vacuum
  6. alldodge

    Trail camera issues fixed, now pics from them ...

    KY has Hunters for the Hungry. This allows hunters to take Deer to a local processing center to be done to give away to food pantry's and low income places. The State pays for the processing Some Counties in KY have no limit but due have a limit on Does. My County has a 4 Deer limit but only...
  7. alldodge

    Alpha I Gen I Hinge Pin 'bushings' ?

    I've done the drilling two 3/4 inch holes on a Bravo but don't know if it will work on Gen 1 Alpha. Most likely would be better to pull the motor, this way everything can be looked at up close JR says no good for Gen 1 https://jrmarine.com/products/alpha_photos.htm
  8. alldodge

    I/O (Sterndrive) Conversion to Outboards

    Yam and Suz are using superchargers which will increase the maintenance and reliability IMO as well. Looks like they are not supercharged, the Yam needs premium fuel but not Suz Hey you could move your CoG more forward if you add more anchor chain :D
  9. alldodge

    Alpha I Gen I Hinge Pin 'bushings' ?

    Don't know why Merc didn't add a bushing with the Alpha, Bravo's have a bushing. As FT mentioned, a good machine shop could add one, and while they are at it, could redo the upper steering pin area. But redoing both could just get a new one
  10. alldodge

    Alpha I Gen I Hinge Pin 'bushings' ?

    No, there is no bushing, LINK The pin isn't wearing, the ring is what wears
  11. alldodge

    Alpha I Gen I Hinge Pin 'bushings' ?

    Is it up/down slop or side to side slop?
  12. alldodge

    Question regarding 1999 Volvo Penta 5.0GL and power to the fuel pump relay

    Carb must be really clogged up, time to rebuild it
  13. alldodge

    New Stuff on Vehicles likes/dislikes

    My 2008 and 2021 Ram diesel had the 6 speed. The 2025 has the 8 speed ZF
  14. alldodge

    New Stuff on Vehicles likes/dislikes

    I deleted my 2008 but "Currently" there are laws on the books which would keep you from ever selling it to anyone other than person to person, unless your willing to take the chance in court
  15. alldodge

    Mercruiser Setting Timing on 3.0L

    Flatness is done with a steel straight edge (can also use framing square) and feeler gauges. Lay edge of straight edge across head and see what the largest feeler gauge can but slipped under it. Max 0.007 overall
  16. alldodge

    2012 90hp Mercury Steering cable

    If your talking about the helm steering box then no. You remove the nut holding the cable jacket and remove the cable. If your talking about disconnecting the cable at the motor end then yes
  17. alldodge

    4.3 GL-D Electrical Issues

    Correct It works the same there as down by the filter I don't see an issue, might just be a loose connection
  18. alldodge

    4.3 GL-D Electrical Issues

    Yes but the oil pressure gauge sensor is normally there. Does the oil pressure gauge work? If it does than sensor is elsewhere
  19. alldodge

    2012 90hp Mercury Steering cable

    @kd4pbs look a little closer, and note hightide said
  20. alldodge

    2012 90hp Mercury Steering cable

    When replacing mine, I removed the helm, removed the nut holding the jacket and rotated helm until the inner cable came completely out. Took new cable feed into helm in reverse order The gray sheath is a protection cover to keep grease from getting over other things under the helm
Top