Search results

  1. Scott06

    OMC to Merc swap in 1996 Sundowner 195

    Yes correct the one pin is unused. I believe they should work. You are smart to get a complete drop in vs piecing it together How is the structure of this boat in terms of transom and stringers?
  2. Scott06

    Stalling when warm

    As mentioned see if float bowl is overflowing or dribbling fuel down after shutoff. Open the throttle is how how clear a flooded engine to start it. would also check fuel pressure if fuel is overflowing the bowl. too high fuel pressure damaged dirty or non functional needle and seat float...
  3. Scott06

    Ticking/clicking noise Mercruiser alpha one 2002

    Did u do a compression test?hard to tell from keyboard
  4. Scott06

    1976 Columbia 16.

    As mentioned look through the restoration section. Unfortunately what you see is likely the tip of the iceberg. The wood in the stringers and the transom are a significant portion of the structural integrity of the boat. I would drill some holes in several places in the stringers and transom...
  5. Scott06

    Hub repair

    the rubber in hub should be putting enough pressure on the prop to keep it in place, over time the rubber degrades loosing its press fit... it is not glued in
  6. Scott06

    Hub repair

    pressed the old hub back in?
  7. Scott06

    OMC to Merc swap in 1996 Sundowner 195

    Do you have the harness out of the donor boat? you could cut the connector off and splice onto your existing boat harness. Or get a used boat harness for the plug. I think this 3 ft harnes could be spliced in to boat harness as I believe the engine has female pins...
  8. Scott06

    Hub repair

    I have not seen the hubs sold separately only had props shops rehub them.
  9. Scott06

    5.7 hard start

    Takes a little suction to open prevents fuel from siphoning out of tank into bilge if their is a leak … Cheap part to replace and rule out
  10. Scott06

    5.7 hard start

    . Spring with a ball
  11. Scott06

    2007 Mercruiser (4.3) Stern Drive

    Either of those mentioned will be fine, no experimentation needed
  12. Scott06

    2007 Mercruiser (4.3) Stern Drive

    Moog 344 or equivalent should work for external clip engine. Spicer makes a cross ref to it 5-3214X if you want a different brand. I have used moog 315G on my gen one alpha no issues. I bought a set of the spicers a year ago when I did my bellows but they were in good shape so I left the...
  13. Scott06

    Ticking/clicking noise Mercruiser alpha one 2002

    Its compression related willing to bet manifold to head, could be loose plug. Wouldn't think you are screwed but need to get in around manifold and head and see where it is coming from. Also wouldn't hurt to do compression check to rule out head gasket. Did it over heat ?
  14. Scott06

    Solas stainless 4 blades all the same?

    might try it with smart tabs removed see if it improves porposing
  15. Scott06

    Solas stainless 4 blades all the same?

    I found the slip on the nemisis/spitfire to be very high too. I think mine was over 20% . You may want to check your dash tach vs a shop tach. You may be reading higher than the engine actually is if the rev limiter is not kicking in. Surprised you cant trim up without porposing
  16. Scott06

    Oil pressure dropping

    Might be worth running a mechanical gauge while on water to verify. I would verify the wot rpm with MM. Forgot about break in. I didn't start running synthetic until after 100 hrs on the engine.
  17. Scott06

    Oil pressure dropping

    I have had some similar instances like this. I also am running a then new 5.0 base engine from MM. I found I would get this when running higher rpm (above 4k close to WOT rpm limit) for a decent period of time like going at WOT RPM for 10 plus minutes. Normally at high rpm my oil pressure would...
  18. Scott06

    1988 Mercruiser 5.7 timing issue.

    Correct no base mode to set on TB 4
  19. Scott06

    Thunderbolt V vs Delco EST Ignition

    YEs no advantage to the delco vs TBV except when you need to replace the module. this parts breakdown that may or may not be for your exact engine shows dist bushings. You can put in your serial number to get an exact fit . I would take the cap off and check the rotor for side to side play...
  20. Scott06

    2007 Merc 5.0 TKS stalled at speed, had to be towed

    Yes the warning alarm switch just disconnect the wire. This switch just creates a connection to ground for the horn. the fuel pump switch you need to jumper out to bypass
Top