Search results

  1. Scott06

    Fuel dumping in 5.0 cobra 1994 mechanical pump, not electric.

    You can get a fuel pump gauge at auto store or amazon very cheap some autoparts stores will loan or rent them. Some replacement fuel pumps are also too high in output pressure. I have seen this myself. You likely need to replace float and needle and seat with good quality parts Mikes carb...
  2. Scott06

    1989 Mercruiser 4.3 LX, Alpha 1 Gen 1 Overheating

    Verify temp gauge is accurate with a IR gun. What's the history of impeller on this drive are you using OEM parts for impellers and housings? Verify PS cooler is clear. What is history of thermostat in this engine and does it have the check balls in T on thermostat housing if they dont close...
  3. Scott06

    1996 mercriuser 5.7 alpha one gen 2

    Either detonation or blown head gasket letting water in cylinder. What do spark plugs look like and was it over heated
  4. Scott06

    Bayliner engine swap??

    Get a merc installation drawing here https://samerwebapp01apncus01.azureedge.net/mmgw-env-b/filer_public/50/c1/50c13579-9b83-41bb-90c9-f0958ee21906/57lalpha_1996-2001.pdf measure where the mounts are and overall size. If your boat was offered with a V8 will fit pretty easy if not might be more...
  5. Scott06

    4.3LX TB IV timing advance issues

    do a little research and see if you can find a factory manual I might be off a few degrees from spec but should be in between the ditches... IIRC total timing should be like 22-24 degrees on it. You can do a little math based on balancer diameter if you don't have multiple marks on the cover or...
  6. Scott06

    4.3LX TB IV timing advance issues

    I don't know the specs for you boat but you likely have a 8 dge BTDC intial setting, then somewhere around 22-24 degrees total at like 2800 rpm. Hook up a timing light with an advance feature and rev it up to about 3 k. you should see the timing advance to keep the it on the timing mark...
  7. Scott06

    Chaparral Mercruiser Prop Question

    I wasn't counting that close.... Your use is similar to mine I have a 2004 Sea Ray 200 sport (20.5') with a 5.0 Carbed engine (about 240-260 hp as It is a 4 bbl Edlebrock carb). It was a 4.3 boat that I repowered so it has the steeper V6 drive ratio (1.81:1). I run a 21" Revolution 4 prop...
  8. Scott06

    Chaparral Mercruiser Prop Question

    I think if you want to do watersports with 8 people ( big ask of any boat) you will need to try a couple props, best to find a shop either local or on line that you can talk with and try a few. I have never used TP props but have read mixed reviews here. I had really good luck with Michigan...
  9. Scott06

    Boat bogs down after 30-90 minutes

    If you get above 170 with a 140 thermostat its too high. You may be sucking air or bypassing too much raw water if you have the check ball system Would not use until you figure this out.
  10. Scott06

    Preloading without the rolling dial torque wrench

    I would say no unless you have one like this. Torque Wrenches, 1/4" Square Drive, 0 - 80 in.-lbs. and 0 - 9 NM Torque https://www.mcmaster.com/7181A22 i used this to set 12-16 in lb rolling torque on pinion bearings
  11. Scott06

    Replacing U-joints Alpha one gen 1

    Not sure what is in manual but you can remove the nut vs chamfering it . There was a post on here where someone said they could get it with out notching you can look for it. Didn’t involve any special tools Here is a video on a gen 2 Either chamfer it or not your call, I don’t care either...
  12. Scott06

    7.4 flame arrestor to KN

    It is the sticker that comes with it when adhered to the windshield that makes the boat faster Seriously good info that confirms most common sense
  13. Scott06

    1989 Four Winns Carrara Mercruiser Alpha 1 Bellows/Gimble Replacment

    I did mine last year gen two but basically same stuff. I made a couple self inflicted errors (shift cable and trim sender/limit) that stretched it out but did it over two weekends. If you are comfortable doing work like this its no big deal. I think the Oem kit at that time was closer to $300...
  14. Scott06

    Mercruiser 5.0 carb?

    Willing to bet your knock system is retarding . Its not the 12 v to knock module its the 8-10 v from knock module to ignition module that is what keeps it from pulling timing out. If yiu see it not advancing i would either get a inline resistor like in a older style points and supply 9 ish v to...
  15. Scott06

    Can’t get on plane

    Do you have replacement gaskets or are you trying to squeeze this in before the weekend ? If you have replacement parts strip it completely down, get a Harbor Freight ultrasonic cleaner and soak it in there. does a great job. Did you get the fuel tank cleaned out yet? no sense cleaning a carb...
  16. Scott06

    Boat bogs down after 30-90 minutes

    With thunderbolt 4 you do not put in base mode set to 8 deg at idle as ‘normal’. Basic timing light is fine I use a timing light and tach/dwell my dad bought in the late 60s …
  17. Scott06

    Can’t get on plane

    Hard to say from my keyboard... I would use something like this https://www.grainger.com/product/1XGR9?gucid=N:N:pS:paid:GGL:CSM-2293:99F1R6:20501231&gclid=EAIaIQobChMIsvTq2ODSgAMVxraGCh1tCA8BEAQYAyABEgI2evD_BwE&gclsrc=aw.ds suck out the fuel into buckets or 5 gal fuel cans. Look in fuel tank...
  18. Scott06

    Mercruiser 5.0 carb?

    Should be a 1.62 on a 22 ft 5.0 boat. I
  19. Scott06

    Can’t get on plane

    Ya gotta get that crap out of your fuel tank and clean the fuel system and carb. There must be a layer of water in the bottom of the tank to get algae in there this tool or something like it is what is needed for the idle mix screws...
  20. Scott06

    Trim Switch Malfunction

    It is a diy possible repair - just wait until you have to do the bellows. Otherwise not worth the work IMHO.
Top