Search results

  1. Bondo

    Engine running 🔥

    Ayuh,.... Welcome Aboard,..... Why not service the raw water pump, before ya go,..??..??
  2. Bondo

    Squeezing more from 5.0L 220hp

    Ayuh,.... 'n if ya wanta get real fancy, use the new ni/cu hard line,..... I did,....
  3. Bondo

    OMC gear case oil filler fitting for pressure/vacuum testing

    Ayuh,.... 3/8"-16,....
  4. Bondo

    Can the base of engine work? Two to bolts under engine are rusted and can

    Where,..??
  5. Bondo

    Sharing fresh water intake from one engine to a second engine

    Ayuh,.... Gen.I
  6. Bondo

    Squeezing more from 5.0L 220hp

    Ayuh,...... Make yer own, outa 3/8" automotive brake line,....
  7. Bondo

    Sharing fresh water intake from one engine to a second engine

    Ayuh,..... Anybody else heard of Globe Impellers,..?? The blue impellers,.... I put one in my ole tin fishin' barge, 4.3LX- Alpha 1,.... Ran it 10 years or more, 'n it was still pumpin' just fine, when I pulled the driveline, 'n junked the barge,.....
  8. Bondo

    Can the base of engine work? Two to bolts under engine are rusted and can

    Ayuh,..... Sand, wirebrush, whatever the drive, 'n paint it,.... That anode plate don't look right either,..... You boatin' in sweetwater, or brine,..??
  9. Bondo

    Sharing fresh water intake from one engine to a second engine

    Ayuh,...... Welcome Aboard,...... Seems it would be awhole lot easier to just service the drives regularly, so the impeller isn't run til it fails,.... Than to build a jury-rig kit, that may, or may not work,.... I'm thinkin' that the bits from the broken impeller are probably...
  10. Bondo

    Overheating issue.

    Ayuh,.... Either down through the y-pipe, or up through the exhaust bellows,..... I've found bits in the backside of a prop before,.....
  11. Bondo

    Loud tapping noise when accelarating under load 3k rpm

    Ayuh,..... Holes in pistons,...... What do the spark plugs look like,..??
  12. Bondo

    Sx-m trim cylinder loose

    Ayuh,..... Once installed, it'll be tight enough,....
  13. Bondo

    1986 Mercruiser 5.7 Engine Rebuild Crankshaft Questions

    Ayuh,.... There's more to rebuildin' a trashed motor, than just throwin' new parts at it,..... You really need a machine shop's services to get it right,..... The block needs to be boiled out, to get rid of all the metal from the failure,.... With a new crank, the block should be line bored...
  14. Bondo

    Loud tapping noise when accelarating under load 3k rpm

    Ayuh,..... Sounds like detonation, usually from bad fuel, a lean condition, or bad timing,....
  15. Bondo

    Sea Ray engine replacement

    Ayuh,..... Welcome Aboard,..... I believe it's worth the expense to do the '96, 'n up motor up-grade,.....
  16. Bondo

    Mercruiser 3.0 blowing ignition fuse??

    Ayuh,..... Welcome Aboard,..... I'm guessin' the underlined might be the cause of the problems,..... The trim pump has a fuse in a holder on it, so look there,..... It might also have the big plastic fuse in it's battery feed,.... Otherwise, there's gotta be something else, that's...
  17. Bondo

    Squeezing more from 5.0L 220hp

    In NYS,..??..?? I lived in Chaumont, on the water till 3 years ago,.... kathy is crazier than andy was, 'n that's Crazy,....
  18. Bondo

    Squeezing more from 5.0L 220hp

    Ayuh,.... It's operatin' range is 1500 to 6500 rpms,..... It's To Big,....
  19. Bondo

    Trim pump brass fittings too big

    Ayuh,..... Welcome Aboard,..... I believe the lines screw directly into the pump, no adapters needed,.....
  20. Bondo

    same speed with different props

    Ayuh,.... Every dyno chart I've seen show peak, at the peak,..... Not arguin', just sayin',...... ;)
Top