Search results

  1. Scott Danforth

    Commonality with Auto Works

    the backup camera in our 2014 sierra is failing...... along with the HMI module and the dash screen is starting to have dead pixels on the OLED screen.
  2. Scott Danforth

    Sealegs don't lift high enough with Frame/Canopy setup

    might be able to make it longer, not sure how they fold in on themselves.
  3. Scott Danforth

    mercruiser 255 inboard 3.4 volts to coil wire

    verify your wiring, you have something not connected and it sounds like a bad connection somewhere you should have about 8-9 volts on the resistor wire there should be battery voltage on the lead coming from the R terminal on the starter only during cranking did you set the points with a...
  4. Scott Danforth

    2005 5.0 gxi-b belt jumped and wiped out,

    VP just buys Gates and Dayco tensioners. They don't make them
  5. Scott Danforth

    1970s winday day cruise foam core deck

    We are experiencing issues. Including us mods. The wizards that control the site have been notified
  6. Scott Danforth

    Maybe my turn for new boat time

    At least it's covered
  7. Scott Danforth

    Sealegs don't lift high enough with Frame/Canopy setup

    a big block of concrete dropped in the water where the aft legs hit?
  8. Scott Danforth

    1985 4.3l v6 mercruiser piston rings

    measure the bores with a bore gauge. you will need more than just the rings unless the block was brand new sitting on a shelf in a time capsule. if it has any hours on it, the bores are no longer round and will be tapered. this means that you will require a minimum of a 0.010 oversized...
  9. Scott Danforth

    Looking for old pictures of powered bimini tops from mid 90s

    Working on a project. looking for ideas on powering a bimini top with an electric actuator. looking for a specific picture I remember. I think it was a magazine article. it was a pontoon boat, about mid 90's with an electric LM style actuator attached to the forward bows, with the bases...
  10. Scott Danforth

    Anyone tried a wireless transom trim switch?

    just remember to seal the open terminals up with marine electrical varnish.
  11. Scott Danforth

    Mercruiser 4.3 L Manifolds

    some may last forever in fresh water. many failed due to core shift issues (cant inspect them easy) and when that happens they kill the motor. Merc started using the batwings you have in 1996 I think they quit using them in 2000 your motor is 26 years old. so why worry about a service life...
  12. Scott Danforth

    Manuals for 5.7

    you need a factory manual Chilton, haynes, seloc all make bad manuals (too much wrong information), they cant be used for toilet paper. they make OK knee pads. however for base engine information. remember, the motor is just a small block chevrolet from a truck with marine stuff bolted to...
  13. Scott Danforth

    1985 4.3l v6 mercruiser piston rings

    Remember, 1985 is a one year wonder. If you're doing rings, you also need pistons and a bore/hone
  14. Scott Danforth

    1985 4.3l v6 mercruiser piston rings

    Some light reading. https://forums.iboats.com/threads/complete-history-of-the-4-3-liter-with-casting-numbers.693935/
  15. Scott Danforth

    1985 4.3l v6 mercruiser piston rings

    GM used mahle rings in 1985
  16. Scott Danforth

    Manuals for 5.7

    You need make, serial number, etc. Here is a link to places to get manuals. https://forums.iboats.com/threads/boat-manuals-owners-manuals.770690/ Base engine is simply a GM 5.7
  17. Scott Danforth

    1970s winday day cruise foam core deck

    The main reason for delamination is too low a density of foam (based on many threads on boat design). The foam starts to break down due to loading If the top layer is delaminated, you need to remove the whole outer skin. I would also take a core sample (about 1" in diameter) to see if the...
  18. Scott Danforth

    Changing outdrive on my inline 6 165 HP.

    MC1/Alpha drive is 75# 2 cases of beer is 80#
  19. Scott Danforth

    bilge pump wiring. My head is going to explode

    Suggest you start your own thread regarding your own boat.
  20. Scott Danforth

    Mercruiser 4.3 L Manifolds

    paying marina prices for both labor and parts, you are looking at over $2500. if you do the work yourself, you are looking at about $750 for the dry break kit
Top