Search results

  1. Scott06

    Shift interrupter switch.

    it was my understanding ( could be completely wrong) that bravo modules do not have shift interrupt feture. I heard thus through michigan motorz when i did my repower seven years ago. I did not want to use the Delco EST that came with a partial engine package so they sent me a thunderbolt...
  2. Scott06

    Water leak to the bilge from transom please help

    Also look on steering pin as well
  3. Scott06

    alpha 1 gen 2 lower unit repaint

    Merc phantom black rattle cans
  4. Scott06

    Engine stalls when accelerating

    Also don’t forget to look at fuel pick up in tank some have a screen inside the tube that clogged
  5. Scott06

    Water leak to the bilge from transom please help

    That would make me think it is bellows so depending on position of outdrive it leaks or doesn’t
  6. Scott06

    Engine stalls when accelerating

    If you are confident in fuel pressure Probably need to strip and rebuild carb cleaning out passages inside
  7. Scott06

    Shift interrupter switch.

    If you are using a bravo ignition module since it was a bravo tear out the shift interrupt will not work Bravo drives with a cone clutch do not require shift interrupt I think you need to swap a alpha module Did you get rid of the belt driven water pump as well ? Not sure if that can be run...
  8. Scott06

    Sterndrive

    Are you locking it in forward by holding the prop ccw with a bungee cord so you cam turn it and the drive shaft splines to align the coupler and drive shaft ?
  9. Scott06

    Boat hit 200 degrees engine temp

    Anodes keep an eye on it if you have a ss prop.. I boat ones at boat zincs.com … had a bunch of corrosion around prop housing . Swapped for oem merc ones seems to make issue go away
  10. Scott06

    Quicksilver ?

    Big f’ ing hammer 5 lb hammer grab the head handle makes a good pushing rod… basically used stuff I had laying around
  11. Scott06

    Quicksilver ?

    I used power tune to make it slippery , I had a storm water piping grate made for a 3” pipe that fit around the ring pushed it in with the handle of a BFH
  12. Scott06

    Boat hit 200 degrees engine temp

    What brand was the offender? Just so folks don’t buy it …
  13. Scott06

    Top end speed

    Define long periods of time … I have run both of my boats (especially the 3.0) between 4-5k towing tubes skiers etc for extended periods Of time 3.0 Lasted 25 years still had great compression (145) when I sold it ran great. On my seventh season on a 5.0 and hit it the same way full boat...
  14. Scott06

    1991 carburated 4.3 fuel pump output.

    No that is not how an antiphon valve works. It is supposed to prevent the tank from siphoning out into the bilge in the event of a fuel line leak, hence why it is located right on top of the tank … yes there is a cracking pressure like a check valve u reference but that is not the purpose of it
  15. Scott06

    Quicksilver ?

    Yes I just did my bellows kept the bearing that came with kit on the shelf and left the perfectly good bearing in place
  16. Scott06

    Exhaust coming out below bellow

    If the exhaust bellows aren’t in water then the boat isn’t in the water …gas fumes are another issue On the trailer my old boat with a 3.0 was louder than my current boat with a 5.0 the water is the muffler…
  17. Scott06

    Exhaust coming out below bellow

    They are holes cast into transom housing so at idle the exhaust doesn’t have to push out 2 ft of water to propeller hub. No adjustment or replacement is needed it’s completely normal
  18. Scott06

    Quicksilver ?

    Agreed only replace if it’s bad /rough. My 2004 still has original graspable bearing. To op nothing wrong with the sealed bearing . If either one gets wet it’s done for …
  19. Scott06

    Hard starts after sitting for a week or so

    Sorry you have to adjust the linkage such that when u pump the throttle it closes all the way maybe 1/16” gap When it warms the coil will open the choke flap completely vertical . The linkages can get corroded and gummed up the heating coil doesn’t consistently work etc
  20. Scott06

    Hard starts after sitting for a week or so

    If choke is only closed till there is a 1/4” you have to loosen up the element and linkage so it does close fully . You should be able to twist it with some effort U pump the throttle to set the choke ( close it ) and power is applied when the engine runs eventually heating up the choke coil...
Top