Search results

  1. Scott06

    1987 4.3l 205 high oil pressure

    Strange they would send a HV oil pump if the engine wasn't set up for it.... Would verify the relief AD is speaking of, i think with out the remote filter it is in the Oil Filter adapter/threaded piece that attaches to the block
  2. Scott06

    2005 Bayliner Capri 175 wont stay running

    Adjust the choke so it closes its there only for cold start up
  3. Scott06

    How much trim?

    A lot of folks will say don't run it in trailer range but I've been doing it for 40 years... and my neighbors too
  4. Scott06

    3 or 4 blade prop for H190 SS.

    Depends on the 4 blade . On my old boat I ran a 19" three blade for cruising and 17" for skiing. I used michigan votex 4 blades which came in even pitches - ended up at same rpms with a 18 4 blade and 16" 4 blade respectively. These didn't have as much bite as the Revolution 4- 21" I run on...
  5. Scott06

    How much trim?

    I have had several boats in the same shallow cove (23-27" deep at end of dock) for many years. So basically I am forced to use the trailer button to trim essentially all the way up (7/8 out or so) just to get it in and out of the hoist, plus 7 min of idle speed out to deeper water. Its a great...
  6. Scott06

    1987 4.3l 205 high oil pressure

    Trying to push more volume through same passages requires more pressure Just curious - How much looser do you run the clearances in this case? Does this provide better longevity at high rpm?
  7. Scott06

    1987 4.3l 205 high oil pressure

    HV pump is not needed. Might also be worth popping a bearing cap and checking clearances. Either the pump has too much capacity and or wrong spring or the clearances are too tight. Try the std volume pump and see what you get. This has some points made in question area below the pump specs...
  8. Scott06

    seriously need some experts help on this one, no water exits manifolds

    Right would think something is wrong as the check balls feed risers constantly, someone must have mixed and matched parts . Is there any advantage to warm manifolds vs cold ones with constant flow ?
  9. Scott06

    Stalls on acceleration under load

    I had to chisel my rotor off did not use loctite to put new one on… You may be able to get the bowl top off with out screwing up the gaskets, you need to clean inside passages not just spray power tune down the bores At least you can adjust float to see if that cures it while waiting on kit
  10. Scott06

    Trim limit switch

    Trim limit switch plugs into the trim pump harness at the pump. Trim indicator sender plugs into engine harness to get sent up to the helm this is for a complete merc setup. Was the entire omc set up torn out or do you have some mix and match
  11. Scott06

    Bought a new long block and wondering about the coupling and gimbal bearing.

    Nice to see the project coming together after all this time. Nice clean install with the factory brackets . Would be interested to hear what kind of AFR you are getting. I'm going to be installing mine this weekend. I put a phenolic 1/2" or maybe 1" spacer under my carb last summer to help with...
  12. Scott06

    1984 28' pontoon I/O repower?

    3.0 with alpha one gen two ‘91 or newer. You will have to close up the transom hole. this is basically the same block as a 2.5.
  13. Scott06

    Mercruiser 5.7 won’t make power

    Thought lift above .420 was too much for stock vortec head as well.
  14. Scott06

    Mercruiser 3.0l TKS stalling

    Agreed idle or transition circuit is plugged
  15. Scott06

    Lots of oil coming from the breather

    A coating yes is normal I get the top of my carb cover with oil, Just wipe it off. Both my old 3.0 and new 5.0 do this.
  16. Scott06

    1997 3.0XL carb rebuild kit

    Always had good tech support from Mike's. Post a picture of the carb we can probably ID it. Does it have one or two idle mixture screws ? If it is the factory carb it will be a mercarb.
  17. Scott06

    Trim cylinders bleeding down fast

    You can leave the atf in there as it will work fine I think I got hydraulic oil with a ISO 32 rating at the local auto parts store that worked fine
  18. Scott06

    Mercruiser 3.0l TKS stalling

    no video or link was attached
  19. Scott06

    Transmission Woes in Vintage Mercruiser

    Some one cobbled this already. Originally grandpas boat came with a white tilt pump and reservoir (combined not separate) that took ATF. Had a very small reservoir that was a PITA to fill. A machinist buddy of his rigged up a pipe attached to it to enlarge the reservoir. Didn't fix the issues...
  20. Scott06

    Spark plug gap difference

    the first paragraph states... "In most cases your Iridium Power plugs do not need to be gapped"
View older results
Top