Search results

  1. Scott06

    Is this a concern?

    Who said anything about a Merlin? Sounds like a good swap though ...
  2. Scott06

    Mercruiser 5.0 Won’t Reach Operating Temp

    this or the gauge is inaccurate. If you have a suspect impeller replace it now as its only $50 of parts
  3. Scott06

    Volvo 5.0GXI Overheat/New thermostat

    It will not come out the exhaust only the water intake ports in the drive I would assume it is the hose that has a flush port on it but I'm not looking at your boat... One of the hoses to the pump will go up to the thermostat housing the other will go back to the transom housing - the one that...
  4. Scott06

    Trim motor bracket replacement....

    Yes just screw into the deck. I would put something like 5200 in the screw holes as a sealant to keep water from getting into holes.
  5. Scott06

    Volvo 5.0GXI Overheat/New thermostat

    Take the water inlet hose off the pump- the one that comes up from transom housing , hook a hose up to it a flush backwards to water intake in drive full flow of water should come out. Look for any leakages or reduced flow. Any thing that leaks going backwards likely sucks air. Also could have...
  6. Scott06

    Is this a concern?

    Depends on the use, my friends 24 ft Crownline deck boat (350mag/300 hp / B3 drive) is underpowered when both our families are in it , touchy to keep on plane. Likely could improve it by swapping Hills props but that's not cheap either. I've owned two boats with the base engine in it, my...
  7. Scott06

    Wonder if I should go IO again or go OB?

    Muc thanks for the responses here- I think your response for how and where you will use the boat is 100% accurate and biggest factor. I do larger inland lake boating aka skiing and swimming, so having the swim platform an sun pad uncluttered is important to me. My brother has a fishing CC so...
  8. Scott06

    Removed raw water pump - rotated harmonic balancer…now what?

    Balancer is keyed to crankshaft and needs a puller to remove
  9. Scott06

    Volvo 5.0GXI Overheat/New thermostat

    Take out the thermostat and test it in pot of water on the stove. what is the condition of the raw water impeller ? Also i think there is a plastic fitting on the transom housing that the hose bringing water up from the drive attaches to that can break
  10. Scott06

    Mercruiser OEM Belt Surprise

    Id be returning that one. Somebody has a sense of humor selling that
  11. Scott06

    Is this a concern?

    Agree pitting shows some electolysis. Grounding or maybe was kept in marina with stray current, easily fixed as said. you didn’t mention what engine is in it. Thats a 23 ft boat with an alpha? May be somewhat underpowered if it is a 5.0. otherwise looks like a clean boat and you dont get much...
  12. Scott06

    Bellow replacement job

    Did not mean that the remote cable would trip the interrupt switch, just that i was rather surprised when properly set up how little effort it takes to move the lower shift cable vs how much effort to shift at the helm. at any rate we are luckily close to the launch so pulling the boat, fixed...
  13. Scott06

    Bellow replacement job

    I got it fixed it wasn’t a shift cable. yes I agree normally replace everything but my shift cable I don’t know if it’s newer works perfectly. I did remove it with the bell housing for exactly that reason What it was was the top bushing on the shift shaft that goes through the exhaust passage...
  14. Scott06

    Bellow replacement job

    I believe it is routed correctly had to do that twice …. It takes more than very very little pressure to shift so I assume something is wrong with cable or work I did to shift mechanism in bellhousing
  15. Scott06

    Can the base of engine work? Two to bolts under engine are rusted and can

    Back fire is usually timing or fuel related Have you done a compression test and you know the timing and firing order is correct ? If yes to both I would think you have a fuel supply or carburetor issue
  16. Scott06

    Bellow replacement job

    so i got the bellows on had some issues of course , tough to get shift cable core back in the stiff part at the front wouldnt go past the bend the outter jacket makes , eventually got it seemed to work smooth … seemd to shift on on land…in water it is engaging shift interrupt going into gear. im...
  17. Scott06

    Maxim 2000sc 4.3lx 4Bbl carburetor question

    9600 is 600 cfm
  18. Scott06

    Mercruiser 5.0 Won’t Reach Operating Temp

    Might be the position of your muffs I found if mine are not exactly right it will overheat even though water is moving through it
  19. Scott06

    1997 Merc 4.3 V6 LXGen+

    Shift interrupt activated ? Try disconnecting see if it rolls
  20. Scott06

    Still no power

    Some tank pick ups have a screen inside them pull the pick up tube and look inside could also be anti siphon valve but as danforth recommended measure fuel pressure at wot If it low tear into fuel supply if it’s ok likely the carb wasn’t done right
Top