Search results

  1. Scott06

    Monster vs Aerial

    I have not installed either brand I did a Krypt Xmobe https://www.bulletlines.com/X-mobe-wakeboard-tower-p/249.htm I am 95% sure this is the same as the Aerial Airborne 2.0 except for the logo. They must be made at the same place, but check out the price diff... I was really happy with the...
  2. Scott06

    Blowby through vent tube? Mercruiser 3.7

    It may be a moot point since they are honoring their work... My thought is ring end gap or mismatch between ring/piston and bore What did the rings and pistons look like from those cylinders?
  3. Scott06

    want to run my engine out of the boat.

    These look like the splices that would go in when someone installs a delco voyager EST (electronic ignition) on an older points or to replace a Merc DDIS distributor less set up that is obsolete. Doesn't necessarily make it bad or wrong as long as it is done right
  4. Scott06

    4 to a 2 barrel carb

    I buy my carb parts from here https://www.carburetor-parts.com/ all good quality parts. never had an issue with any parts or kits over ten plus years of buying from them for my boats and classic cars.
  5. Scott06

    Boat swamped, let's see if we can get it running...

    no i think there is a cavity in front of the driveshaft in the coupler. Will not end up in bellows. I usually give mine 3-4 pumps in the fall was still greased when i removed the drive
  6. Scott06

    4 to a 2 barrel carb

    As outlined you should be able to get and adapter and adapt the rochester or mercarb two bbl to the manifold, but might require rejetting the carb. How bad di the PO screw up the carb? If you have a good core I would recommend having it properly rebuilt either locally or someplace like this...
  7. Scott06

    Water in oil

    Probably more a matter of what cylinders exhaust valve was open when you stopped it. I do believe the water in the cylinder will slowly leak past the rings into the oil. If you test the cooling system with air pressure and it holds you know the leak is from the manifolds To elbow joint...
  8. Scott06

    Water in oil

    Yes water is likely leaking back into cylinders. Would pressure test the cooling system
  9. Scott06

    Ran outdrive without lube! Bad sound.

    If you are getting it rebuilt for the cost of an SEI upper he is being very fair on price.
  10. Scott06

    Truck cam with captain's choice?

    Not sure what the original engine was in terms of initial and total timing. I think merc vortec 5.7s will have 10 deg initial and total of 30-32 ish by 2800 or 3 k rpm.
  11. Scott06

    To fuel filter or not. 3.0

    Agreed . I have never seen a 3.0 with separate canister fuel filter from the factory. My folks had a 91 seray with a 3.0 that was passed down to me. I changed the filter that was a sintered stone for the first time when the boat like 18-20 years old … spring in bottom of housing Was rusted out …
  12. Scott06

    1995 Searay 5.7 GM winterizing mods..

    Unfortunately the idea i have is to lull the engine and retap or heilcoil correctly. Can you start the tap in there? If not likely plug or nipple is busted off in there.… dont think they make expansion plugs that small
  13. Scott06

    Blowby through vent tube? Mercruiser 3.7

    X 2 on this and in post 1 OP states he used break in oil and followed a reasonably proper break in regime.
  14. Scott06

    Blowby through vent tube? Mercruiser 3.7

    Yes yours are the opprosite of lean and detonation…here is a plug reading guide http://wallaceracing.com/plug-reading-lm.html
  15. Scott06

    Blowby through vent tube? Mercruiser 3.7

    Not enough oil comes out the vent and into the carb. take plugs withyou to the machine shop, they are going to say it was lean , but your plugs are not lean at all… in fact oil and rich… the plugs look like the ones out of my 65 gto. I did a backyard hone re ring, bearing, new cam, valve job…...
  16. Scott06

    Small amount of water in gear oil.

    So im not sure should i do this? I dont recall seeing 5-20 on the shelf 25 years ago 5-30 was the new kid on the block back then
  17. Scott06

    Boat wont turn over…Safety Switch?

    Yep, if you hear the starter engage and click then look at engine/gimbal/ujoints/drive being locked up, but thats not whats happening here
  18. Scott06

    want to run my engine out of the boat.

    Could have been the key switch or neutral safety switch. What Bondo recommends is a very good start clean and tighten all connections. Under the dash often times 12v supply to the switch and 12v back to ignition on are often daisy chained through the gauges- lots of potential for loose...
  19. Scott06

    want to run my engine out of the boat.

    Could have been the key switch or neutral safety switch. What Bondo recommends is a very good start clean and tighten all connections. Under the dash often times 12v supply to the switch and 12v back to ignition on are often daisy chained through the gauges- lots of potential for loose...
  20. Scott06

    New Engine Replacement - Engine Died and Hydro locked after 5 hrs!?

    I understand pulling the kill switch at rpm will create hydrolock potential… both are killing the ignition…and i think engine can spin backwards when it sputters .
View older results
Top