Search results

  1. alldodge

    Volvo Penta 5.0 GXI-E - Won't roll over

    The lines should not need any tape.
  2. alldodge

    Lowering the bunks . . .

    If lowering doesn't get you where you want, could change to low profile LT tires. something like 205 or 195 10 ply
  3. alldodge

    5.0 GXI Cracked Block Need Help Sourcing New Parts

    Not going to be able to use the ECM on anything but a stock 5.0
  4. alldodge

    2005 Triton FS 18

    Should be where all are Was there any water in the boat when you pulled it out?
  5. alldodge

    Constant 'Two Beeps' from my Four Winns 4.3

    Yes,
  6. alldodge

    5.0 GXI Cracked Block Need Help Sourcing New Parts

    long block https://www.michiganmotorz.com/5-0l-vortec-marine-engine-1996-current
  7. alldodge

    Constant 'Two Beeps' from my Four Winns 4.3

    I called it a switch but its actually a sensor, and it tells the ECM if water pressure after the raw water pump is low. Located above and at the rear of the motor on the power steering cooler, item 14 in link post previous Yes it does look a little low. It should not be full but right at or...
  8. alldodge

    Volvo Penta 5.0 GXI-E - Won't roll over

    No, it's there to keep excess grease out or bilge and help keep dust out, can be reused Most all the new gimbal bearings are sealed and no longer greased. Check to make sure your bearing has a hole in the race so it can be greased
  9. alldodge

    4.3 runs great for about 30 minutes then bogs, pops won't accelerate

    The jumper doesn't "clear" base timing, it puts it in base timing mode so it can be timed.
  10. alldodge

    Constant 'Two Beeps' from my Four Winns 4.3

    Serial shows 555 ECM The highest failure rate item on your motor is the sea water pressure switch. I'm not saying that's the problem it's just they fail often The pump above is the Trim pump, it raises and lowers the drive. The power steering pump is belt drive and on the front of the...
  11. alldodge

    4.3 runs great for about 30 minutes then bogs, pops won't accelerate

    I merged your 3 threads because they are all about the same thing
  12. alldodge

    Volvo Penta Ignition Switch

    Finding something about anti restart. So is it the new type like Mercruiser which shuts the motor off if you try to restart while it's running? Mercruiser is about $50
  13. alldodge

    please help timing issue is the expected issue help!

    Turn key to start and hold, then with other hand move shifter slightly FWD/REV. If it cranks then is the neutral safety switch in the control If not look for the slave relay on the motor next to the 50 amp breaker. The slave is what jumps the starter
  14. alldodge

    Bravo III Mixing Prop Materials

    That is a stainless 24 pitch
  15. alldodge

    How to wire wiper motor

    Made a search and have been unable to find any instructions or diagrams. Does appear you wired it correct, guess the question is I've seen nothing that tells me it will park
  16. alldodge

    1989 Mercruiser 4.3 LX, Alpha 1 Gen 1 Overheating

    Don't know how to test upper elbow, but lower and place rubber piece between Man and elbow to pressure test lower Man
  17. alldodge

    2008 4.3GL Distributor Hold-Down Screw

    Now that's just out and out BS It's one thing to do this kind of thing during warranty period, but after VP should be "required" to remove and replace with a regular bolt. Previous thread on Iboats shows the hex head to be 5.5MM and not standard 5MM...
  18. alldodge

    Bravo III Mixing Prop Materials

    Welcome Don't know of a B3 prop set front or rear which is made of aluminum, all are SS Merc made what is called XR series (4 blade front, 3 blade rear) but all are SS. It's your drive but that is a $10K+ gamble
  19. alldodge

    Flow reducer in Y Pipe?

    Geezers, don't know who put that together, but never seen anything like it. Don't know what the hose that goes from the top of one Man to the other is even should do. It's not closed cooled, so those hose have no effect. My initial thought is remove and plug the Mans where hoses where...
  20. alldodge

    How to wire wiper motor

    Welcome We're gong to need more then you have a wiper motor. Might have been bought from WM but need to know who manufactured it? Part number, something like that?
Top