Search results

  1. dingbat

    Add a battery switch installation

    If you have an existing battery switch, it should be connected the ACC post on the back of the switch
  2. dingbat

    Tahoe 2150 Bulge Pump Issue

    Try looking under the motor
  3. dingbat

    Has anyone installed trailer guides?

    Guessing either your bunks are not setup properly and or the trailer is too deep. With the bunks setup properly and the trailer at the proper depth, the boat should self center and “run around” 16 to 18” short of the bow stop. With front of boat sitting squarely on the bunks, the rear should...
  4. dingbat

    Need second battery pointers

    If your going as far as to separate the ignition and house loads, you might as well install an ACR while your at it. My boat came OEM with two batteries but the “house” was simply a backup with a 1/2/Both switch. It wasn’t until I installed a full complement of electronics on the “house”...
  5. dingbat

    2004 225 oil injector issue

    I won an all expense paid trip to the Midwest last week to trouble shoot what turned out to be a water flow sensor stuck open. The computer said everything was working properly. Water flow was good yet the system shut down from over temp. Moral of the story….don’t assume anything. First...
  6. dingbat

    Pro craft 1660 V Livewell pump

    What make and model pump. Resistance? Not sure what that has to do with a live well pump. Your looking for 12vdc
  7. dingbat

    Circulation pump

    Did they specifically say 304 stainless in the advertising? 304 is Austenitic and should not be magnetic but if there secondary work was done to the parts all bets are off. The process of stamping and surface polishing can change the micro-structure of S304 and thus create martensite The...
  8. dingbat

    AC power when switch is off?

    Never heard of a breaker failing closed but there is a chance the contacted arched, welding themselves closed Easy enough to check. Pull it out and put a meter on it
  9. dingbat

    Will it fit?

    A new axle for my 30’ lg. tandem trailer is $350 Can only imagine what condition a $350 replacement would be in
  10. dingbat

    3.5 hard drive

    Pretty sure USB doesn’t power the drive. Data only. I had to use a pigtail power adapter to dump my old laptop data to a new SATA drive
  11. dingbat

    Decent reels??

    The Okuma Avenger series is the best “cheap” reel on the market
  12. dingbat

    Has anyone installed trailer guides?

    I guess it would depend on the rub rail design and quality My rub rails are “rigid vinyl with an insert. The lower durometer material resists marking, dings and scratches rather well. Certainly not going to be permanently damaged or marked by pvc https://www.integritymarinecorp.com/grady-white...
  13. dingbat

    interrupt switch disconnected

    Depends on the quality of the boat, hardware and dock I've had twin 200 HP outboards tied to a dock in gear numerous occasions. How much HP are you dealing with?
  14. dingbat

    New to me boat trailer: Safety chain and loading with bunks.

    done
  15. dingbat

    New to me boat trailer: Safety chain and loading with bunks.

    I used a turn buckle on mine. The boat isn't going anywhere
  16. dingbat

    Outboard Flex Tube

    Here is the stuff if you can find a local supplier https://www.electriflex.com/products/type-clr/
  17. dingbat

    2007 Tahoe Boat Trailer

    https://www.trackerboats.com/learning-center/trailers.html
  18. dingbat

    Outboard Flex Tube

    Most the OEM “tubes” are “bolt-ons”. A lot better than the various aftermarket adaptations and work arounds. Having said that, eBay is your friend for this type of stuff
  19. dingbat

    Adding a House Battery to Bayliner VR5

    I think we’re talking two different things. The only 2,4 and 6 awg wires are battery cables. The term “jumpers” would lead to suggest the cables running from ACR to each battery and or the battery cables proper. If that is the case, duplicate cable size with existing battery. The cables...
  20. dingbat

    Timken part # for alpha gen2 cone bearing + race

    The fact that they changed the design would point to an inherent problem with the original design or a supply issue. Old design parts costing less than new would suggest supply issues with planned obsolesce, i.e. selling existing inventory at discount to unload
Top