Search results

  1. Scott Danforth

    496 HO Failure

    Gen VI and VII BBC's will spit rod bearings for #3&4 if you run them low on oil
  2. Scott Danforth

    Top

    that is a camper canvas. see your local marine upholstery and canvas shop. they can make one that will guarantee to fit.
  3. Scott Danforth

    Star Tron added to Jetski's now they will not start

    there is no mechanic in a can. I would drain the tanks and run the fuel in your car. then service the fuel system on your wave runner.
  4. Scott Danforth

    350Magmpi

    Once you pull the fuel filter, you contaminated the clean side
  5. Scott Danforth

    New boat with merc 5.7

    If you got a flame, you have spark How long did the boat sit? Carb or EFI?
  6. Scott Danforth

    Bimini top 1989 Funliner

    Get a Bimini that attaches to the tower
  7. Scott Danforth

    350Magmpi

    You didn't reuse the filter, did you?
  8. Scott Danforth

    Volvo Penta SXA Drive ripped off boat.

    Contact your local VP dealer with engine serial number a d they can tell you exactly It will be an SX-A, however which ratio will come from the dealer
  9. Scott Danforth

    Fuel delivery

    They are not that expensive
  10. Scott Danforth

    Volvo Penta SXA Drive ripped off boat.

    You need the same drive that was on there Don't even consider OMC, while some of the early JV drives were rebadged VP drives. That was the 94-99 era.
  11. Scott Danforth

    Fuel delivery

    Seloc, Haynes and Chilton are know to have the wrong information.
  12. Scott Danforth

    Best prop?

    As with all prop questions The important ones What is the max WOT RPM your motor is supposed to be turning What is the max WOT RPM you are getting? These are the important two There are others in the prop sticky Additionally, is your pontoon motor height set correctly?
  13. Scott Danforth

    Fuel delivery

    Factory manual? Hope you didn't waste money on a Chilton, Haynes, Seloc or other non-factual, non factory manual
  14. Scott Danforth

    350Magmpi

    Without the engine load reference signal (vacuum) the pump should be pushing about 50psi I would be looking at inlet restrictions
  15. Scott Danforth

    Ercoa Pontoon boat how to drain tube??

    They are vents to equalize pressure so your toon logs do not fatigue crack. The red plug is so you don't sink if you get a leak on the bottom Drop a 1/4" hose down the vent port. I usually use a bit of lead wrapped around the tube. Get the tube to the bottom of the log. Then using an air...
  16. Scott Danforth

    350Magmpi

    Your fuel should not drop below 43psi
  17. Scott Danforth

    230A condenser failure

    File the points Key on voltage should be 9 volts, just like running. Cranking voltage will be battery voltage
  18. Scott Danforth

    Rehab SportCraft 222 1983 deep V hull cuddy walkaround

    Use z-clips and 1-1/4" x 3/4 slots in the substrate to mount the panels if you don't want to see hardware
  19. Scott Danforth

    230A condenser failure

    Yes, you are getting it wrong. You went down a rabbit hole in resistance and ignored what we are telling you on reading voltage With the coil mounted and wired in the boat. What is the voltage between lock ground and coil + during both cranking and running.
  20. Scott Danforth

    2004 Mercruiser 3.0 Won’t start, misfires & runs rough when starts.

    check timing while cranking which ignition system?
View older results
Top