Search results

  1. dingbat

    Gathering Components for adding GPS to Older VHF

    Ok....here is the manual for plotter https://www.furunousa.com/-/media/sites/furuno/document_library/documents/manuals/public_manuals/gp1670f_1870f_operators_manual_ver_f.pdf Bottom line...the two units are not compatible from a communications standpoint. The plotter doesn’t support NMEA 0183...
  2. dingbat

    Mariner Center Console rod holder inserts?

    Looks and sounds (dim wise) more like cup than rod holders. Could have simply had edge molding in the inside or perhaps even a trim ring
  3. dingbat

    Running spare hot wires....

    Internet parroting of old wives tales. Been using individually shielded wire cable on transducers for years. 95% of the time, “noise” is the result of poorly designed electronics, maintenance related issues or deficiencies in the installation of the unit. Buy a well engineered, good quality...
  4. dingbat

    Question about Trolling Motor Plug and Receptacle

    Goggle - pcb conformal coating spray for your options We send our PCB out to be dip coated. No real experience with spray on coatings. Got to be better than nothing. Maybe replace with "Riptide" controller next time
  5. dingbat

    Question about Trolling Motor Plug and Receptacle

    What model trolling motor? From what I can tell, the "Riptide" Series is the only model "optimized" (power coat and sealed control PCB) for marine use. The recommended plug for "marine use" is https://minnkotamotors.johnsonoutdoors.com/accessories/trolling-motor/plug-receptacle-mkr-26 There...
  6. dingbat

    Question about Trolling Motor Plug and Receptacle

    The problem isn’t salt water.......the problem is (junk) connectors and or wiring not designed for saltwater use. If you have SW compatiable components, you have a grounding issue
  7. dingbat

    2002 HPDI Hrs

    20 year old motors with 2k hours..... no thanx
  8. dingbat

    Gathering Components for adding GPS to Older VHF

    Can’t get anymore direct than using the existing NMEA connections. If you can’t get your head around splicing the pigtail I posted above to the NMEA wires coming out of the back of the plotter, don't know what to tell you. Your turning a mole hill into a mountain range....
  9. dingbat

    Mariner Center Console rod holder inserts?

    Diameter? Deep below?
  10. dingbat

    Mariner Center Console rod holder inserts?

    Never seen just "holes". Always tubes with gimbal pins. Picture?
  11. dingbat

    So, what did you do today?

    IMHO Prefinished or Engineered flooring is terrible at any price. SIL whines about her "wood" floor getting wet or the dog scratching it all the time. Had 2" red oak in the last house. Random width, wide plank pine in this one. Floors where installed when the house was built in 1978 and...
  12. dingbat

    Cup holders?

    Yep....or you can buy the cheap ones that rust and look like krap in 10 months for $12 each.
  13. dingbat

    Mariner Center Console rod holder inserts?

    Usually brand and model specific. Google is your friend....
  14. dingbat

    Just thought I'd share a nice photo.

    Above and below
  15. dingbat

    Gathering Components for adding GPS to Older VHF

    Both are older, discontinued units. Neither unit is NMEA 2000 compliant. No short cuts here. Need to use NMEA 0183 connections. Solder RCA connector to Tx and Rx (NMEA 0183) connections on plotter Don’t remember if you need a male or female RCA but this is what you need...
  16. dingbat

    Gathering Components for adding GPS to Older VHF

    The VHF is a good unit. Have one on my boat as well. Don’t understand the need for a 12 to 5v adapter. Position is coming in from the plotter via the RCA connection
  17. dingbat

    Running spare hot wires....

    Why would you have a problem if the wire isn't actually used, i.e. "Spare"? Either way, no problem if the the unit is properly grounded.....transducer cables are shielded. Just don't try pushing 220 VAC through the wire...lol
  18. dingbat

    Gathering Components for adding GPS to Older VHF

    UR IDC connectors are the way to go 19-26 awg. Easy to use and provide a water proof connection
  19. dingbat

    Cup holders?

    Good guess but not the correct answer.....won two all expense paid vacations to Sweden and one to Spokane WA on this very subject. You actually have two issues.... the machining and tooling process temporarily removes the materials protective oxide layer. The resulting contamination (oil, dirt...
  20. dingbat

    Gathering Components for adding GPS to Older VHF

    What GPS do you have? Scratching my head about the interface box. I see no reason for it. All your doing is adding a RCA connector to the TX and RX connections (bare wire) on the chart plotter. The wire(s) from the gps antenna go directly to the plotter as well.
Top