Search results

  1. dingbat

    Why my leaf springs are sliding?

    The "keeper" you mention are called "rebound clips". Their function is the "share the load" from one spring to the other. Holding the spring in place is the function of the "central clamp" i.e. u-bolts. https://www.engineersedge.com/material_science/leaf-spring-design.htm
  2. dingbat

    Water in gear oil?

    Looks like the emulsifier in the gear oil is working. "Emulsifiers have been added to protect internal components in the event that water enters the gear case" Differently water, but not much.
  3. dingbat

    Why my leaf springs are sliding?

    I don’t have keepers on mine either. The whole spring is sprung. Hold down clamps have shifted as well. Guessing one of two scenarios: 1. One or both of the lower springs have broken. 2. The clamp was not torqued to specification and shifted Replaced my springs as PM two years ago. Had a...
  4. dingbat

    Quick confirm: oil mix

    Here is a technical paper that addresses the issue given at the Annual SAE meeting June 1963. Looking for the full paper Paper is focused on reducing 2 stroke emissions to compete with the up and coming 4 stroke motors Lots of papers on 2 stroke oil development to support leaner mix ratios in...
  5. dingbat

    Question about new Dell Inspiron computer

    The new drive is a 1 Tb drive......just copy the old onto the new and be done with it. I have the contents of my last 3 laptops (commercial data) loaded on my current laptop with a 500 Gb drive. A little less than 30% full.
  6. dingbat

    Quick confirm: oil mix

    Or... that it did anything other that met minimum performance standards which are a joke..... Pass Fail Criteria: To be considered acceptable for certification in TC-W3®, a candidate oil must pass the following criteria: 1) Compression Loss: No cylinder compression loss of equal to or greater...
  7. dingbat

    Isolating house loads for dual battery setup

    The ignition is typically powered via the battery cable. A lot of times the “house” load is tied directly at the battery terminal by a secondary wire Bear in mind that should your house battery take a dump, you can’t use the starting battery to power the “house”. If you have critical needs...
  8. dingbat

    Rigging boat for dry dock lift.

    Grady White boats Optional equipment
  9. dingbat

    Nobody fishing?

    Took the week off and ran down to the honey hole (Cape Hatteras) to see of the big Reds made their appearance out front yet. Normally I go the first week in November, but we took some friends that wanted to get in some beach time. We caught lots of fish but nothing big. Saw a 5-6 ft. Spinner...
  10. dingbat

    Rigging boat for dry dock lift.

    My boat is designed to be lifted that way using two, thru-bolted eye hooks on the transom and the bow hook
  11. dingbat

    Yamaha 115 V4 Salt Water Series Running very smokey

    First thing I'd do is pull the plugs to determine if it's a problem with an individual cylinder(s) or a systems (oiling) problem. If nothing obvious shows up, run a compression test. Nothing there I'd look for a fuel or vacuum leak. Either will cause over oiling
  12. dingbat

    Radar Question

    The stand alone Si-tex is your best option.
  13. dingbat

    New NGK BR8HS plugs improve overall performance

    Been using the Racor clear bottom filters on my personal boats as well as commercial applications for many years. None have ever leaked. Either the filters in question are inferior or people are trying to adapt filter’s components between brands which by design doesn’t work
  14. dingbat

    New NGK BR8HS plugs improve overall performance

    What brand are you using? Never had one leak
  15. dingbat

    Deck plate question?

    I have four pry out and 2 screw in deck plates. None of them leak. To leak, you either have installation (frame) or o-ring (cover) issues. First thing I’d try is o-ring lube. If that doesn’t solve the problem you have an issue with the installation of the frame. The frame must be flat...
  16. dingbat

    Multifunctional Gauges

    While I’m not a HB fan for a number of reasons, electronics are constantly evolving. I would check to see if there where any software updates done to make the unit fully NMEA 2000 compliant. If not, Garmin offers a number of ways to do this including a stand alone display specifically for...
  17. dingbat

    Multifunctional Gauges

    NMEA 2000 is a standard communication protocol (language) to allow “plug and play” connection of peripherals between different instrumentation manufacturers. The tach function is supported in the NMEA 2000 standard. All you would need is a convertor/gateway, in your case MercMonitor, to convert...
  18. dingbat

    Vessel View Installation

    I started digging into this a bit for you this morning. If all you need are the NMEA 2000 PGNs to feed a NMEA 2000 compatible display, you can us the "Merc Monitor". Vessel View is an "Display Package" for use on Lowrance and Simrad displays using a proprietary (non-NMEA 2000) communication...
  19. dingbat

    Lead Paint in 1976

    Lead based paints where in common use through 1978. The probability of your boat being painted with a lead paint (or anything else painted prior to 1978) are close to 100% Having said that, lead has to be ingested or inhaled to cause issues. If the paint in good condition it posses no...
  20. dingbat

    Chunks on Spindle

    A stiff wire brush typically used on a grinder. Will shine that shaft up like new in no time https://www.homedepot.com/b/Tools-Power-Tool-Accessories-Abrasives-Grinder-Accessories-Wire-Cup-Brushes/Milwaukee/N-5yc1vZ1z18gvhZzv?storeSelection=
Top