Search results

  1. dingbat

    New V6 head gasket - sealer or no sealer?

    I picked up the new heads gasket for my 97 200hp Ocean Pro. The gasket is shiny on one side and has some sort of a grey sealing "band" around the perimeter of the bolt holes on the ?block side?. The head has been machined but the block sealing surface is much to be desired. I got the block back...
  2. dingbat

    97 200 HP Ocean Pro head gasket

    In the fall of 2006 my shop found evidence of water in the lower cylinder on the port side and changed out the head gasket. At the time I was told there was considerable corrosion and that leakage in the future may become an issue. Since that time there has been no evidence of water and the...
  3. dingbat

    How many hours do you have on your outboard?

    Lots of longevity claims based on age but very few with actual hours of use. As with anything mechanical it?s the amount of useage and not the age of the equiptment that's important. How many hours do you have on your motor? Me: 1997 200HP Evinrude Ocean Pro = 2112 hours for a 192 hours a...
  4. dingbat

    Radial or Bias tire for a tandem trailer

    I have my ideas and experiances but what are yours and why?
  5. dingbat

    Problem with FM reception

    I have an 8' FM antenna on the boat. The reception is great and I've never had an issue picking up stations in the area. Friday I backed the boat into the drive to clean it up for an upcoming charity event. While I was up cleaning the top I noticed that any time I got close to the anntena or...
  6. dingbat

    Nothing sweeter than the whine of Quad 300's

    http://www.youtube.com/watch?v=3mMlS2bQBAs
  7. dingbat

    Electronics or fuel delivery? 200HP Ocean Pro

    The motor has been running great but the last couple of times out it acted funny first thing in the morning. It will fire right up and idle but after a couple of minutes it sneezes for lack of a better word and then shuts down like someone turned the key off. Not a stumble, nothing. Just...
  8. dingbat

    Are 4-stroke carbureted Stern drives bring down the industry

    http://money.cnn.com/news/newsfeeds/articles/prnewswire/LATH01114022008-1.htm
  9. dingbat

    Lower unit oil for high HP application

    I need to change my lower unit oil. Not sure what oil the shop used when the LU was torn down for repair this spring. What's the best LU oil out there for a high HP application. The motor is a 200 HP Ocean Pro
  10. dingbat

    4 blade props

    Does a 4 blade prop act differently at high RPM than a 3 blade? I have a 4 blade Renegade (14 ? x 17) on the 22’ walkaround with a 200 HP Ocean Pro . I certainly can’t complain about the holeshot. For a boat as heavy as it is it gets out of the hole nicely and cruises well at 26-27 knots @...
  11. dingbat

    A bit rough idle / Wet carb gaskets -1997 Ocean Pro

    The motor is running well but it's a bit rough at idle. Maybe its the nature of the beast but I have a hunch that its a sticking float or needle valve. The carbs had been rebuilt last fall so I was surprised to find that all the bowl gaskets where wet when I replaced the fuel lines the other...
  12. dingbat

    1997 200 OceanPro surging at idle

    The motor ran well all day while trolling @1200-1500 rpm. Dropped it out of gear to pull in the planer boards and it was surging at idle. Didn't look at the tach but I figure up and down maybe 100-300 rpm. Drop it back into gear and it idled like normal. Ran 5 miles back to the marina @4500...
  13. dingbat

    GPS accuracy question

    Just wondering how big a difference there actually is out there. What kind of antenna do you have on your GPS unit, built in or remote? How many satellites do you typically lock on to and what’s your typical postioning accuracy? I have a remote antenna and receive a full compliment of...
  14. dingbat

    Mouth of the Merrimack claims another boat.

    'You couldn't believe your eyes'; Sinking renews worries about wakes, overloading boats By Stephen Tait , Staff Writer Eagle-Tribune ­ NEWBURYPORT - The first wake hit the overloaded, 17-foot-long boat and got it rocking back and forth. The second one filled the vessel with so much water...
  15. dingbat

    Renegade offshore

    I'm currently running a 14 x 17 Renagade Offshore on a 200Hp Ocean Pro pushing a 22' WA (hardtop and all) at 38 MPH@5350-5400 rpm. Performance overall is generally good, good hole shot, top end is satisfactory, but mid-range cruise seems weak and the bow tends to drop on anything under 4K rpm...
  16. dingbat

    1997 Evinrude 200 water pump

    I had the lower unit resealed and they changed out the water poump while they had it torn down. I kow have about twice the pressure (pegs the dial at WOT) I had before so I'm guess they put in the wrong water pump. Is it OK to run the higher pressure pump or should it be changed?
  17. dingbat

    Miss/ misses on a 97 200 hp Ocean Pro

    My mechanic is trouble shooting a problem on my motor and just isn’t getting anywhere. He says he’s never seen anything like this in all his years in the repair business. The symptoms are as follows: There is an intermittent miss in the #1 cylinder at idle and an all out miss in #1 and #5...
  18. dingbat

    Spit, Pop and Burp. 97 200 Ocean Pro

    Thanks to all the good info I received from here I've worked through everything and got it to idle fairly but I have two remaining issues. The first is that it "burps" now and then. What I mean is that it will instantaneously drop revs, burp a puff of smoke, and then jump right back up and idle...
  19. dingbat

    Pulse limiter has check valve?

    The manual says that the pulse limiter has an internal check valve however I can blow right thru mine in either direction. Is this normal or is the check valve stuck open. Time for a new one? 1997 200 Hp Ocean Pro
  20. dingbat

    Plug quesion?

    Doing a little trouble shooting on a motor not that is running bad but but not running well either Took it out and ran it about 25 miles at cruise (4000-4200 rpm), Camew back and hecked the plugs (77YJ4?) look nice and creamy on one side and brown/black on the other. Plugs generally looked...
Top