Search results

  1. R

    Intermittent water

    Pumps are not self priming.-----Water must be 8" above the IMPELLER.-----When running in a test tank you may get exhaust into the pump.-----These pumps do not pump air.
  2. R

    Olympics

    I used to curl a bit.-------It is a chess match on ice.------You get a warm feeling of scoring a few points.-----Then your opponent throws one 40 lb stone and they score 2 points.-----Frustrating !
  3. R

    Intermittent water

    Model # of this motor ?
  4. R

    Intermittent water

    The water in your test tank MUST be 6 or 8" above the impeller.-----Just covering intakes is not good enough !
  5. R

    Best out board motor lock

    A hidden bolt / s through the transom might work.------If the culprits loosen the motor clamps they expect to walk away with the prize.-----They may not want to turn on a flashlight .----They might move on.
  6. R

    1948 Evinrude 3.3hp carb

    When I look at the breakdown of a carburetor like that it becomes obvious as to why fuel injection has taken over.-----Fuel injectors are cheap and easy to make.
  7. R

    Hook up boat engine to permanent magnet generator.

    Most folks are unaware of how much horsepower goes into the grid.-----I have often asked folks how much power it takes to turn just 1 ( there are 8 of them ) generator where I worked.-----The most common guess is 10,000 HP----When in fact it takes 1,000,000 HP.------When all the electric...
  8. R

    new to me 1970 Johnson 25hp tiller short shaft. locked up

    In order to hone cylinders the motor must be taken apart.
  9. R

    125 Force Outboard won’t achieve full power

    Post your compression numbers tested today. -----Might be running on 3 of 4 cylinders.----Test spark.-----Check fuel pump diaphragm too.
  10. R

    My '55 5.5 outboard

    That o-ring is very common.-----Still installed in 2007 motors as well.----Local boat shop would have that o-ring in stock at about $4 or $5
  11. R

    Spun hub 1985 johnson 15 hp

    Block of wood and a hammer might do it.----Or run to your local boat shop , they will likely have it off in a heartbeat.
  12. R

    Spun hub 1985 johnson 15 hp

    5/16" threaded rod.-----Make a J-hook and slide hammer.
  13. R

    SeaSenor

    Warning horn for overheat??------What motor , what power , what year , serial # ????
  14. R

    `97 Fast Strike 150 trim/tilt issue

    Agreed.----he said that he had to disconnect.---He also clearly stated that after reconnect nothing worked.----So some simple testing needs to be done !!
  15. R

    `97 Fast Strike 150 trim/tilt issue

    Find the plug for the trim tilt.----Green and a blue wire.------Apply 12 volt directly to to those terminals.----+ to one wire and - to other.-----See if motor works.
  16. R

    Olympics

    The Chinese folks are even a bit upset that their hockey teams are mostly ( if not all ) imports.----Some even have adopted Chinese names.-----What a joke these Olympic games are becoming.------All about money for the Olympic organizers.----Not an amateur thing by any stretch anymore and has not...
  17. R

    Olympics

    Not into it as much as before.-----There are so many other thing to watch these days.------Namibia cam---- in the desert with various animals at a water hole.-------Deer at the ---brownsville pantry-----In Maine.------No politics and money concerns for the animals.
  18. R

    Hook up boat engine to permanent magnet generator.

    I used to be ( 30 years ago) involved in an " emergency response crew "------Vehicles we drove had a 120 volt system to run air sampling units.----The technology is out there.
  19. R

    Boat identification help needed!

    Depends on your location for the paperwork.------But a boat like that is easy to repair / restore.-----You could even make it better and stronger than it was new.-----But it won't be cheap.------Depends on what you want !
  20. R

    Lower Unit Shift Rod

    Put throttle control in idle position.----You pull the bottom rod UP.------You put the top shift rod all the way DOWN.-----This gives you room to work.----It goes together and it should all be lined up and working as before.----Done this many times !!---Bottom shift rod turned all the way in...
View older results
Top