Search results

  1. alldodge

    Fuel guage and tilt guage not working 88 nordic

    Without more info, look for a fuse or broken wire
  2. alldodge

    Mercrusier 5.0 MPI (2008) RPM stops @ 3200.

    The 3200 rpm could be the In-Gear switch but your not getting an alarm. The switch is on the shift plate and you can disconnect it to see if the issue goes away Would be best to scan for codes, but without need fuel pressure reading
  3. alldodge

    Engine starts and dies.

    Code 0342 - Camshaft sensor lost. Motor will not run with this fault Code 0643 - 5V high. This is set when 5V reference is above 5.4V. I'm not seeing in the print out where it list above 5V, but if a sensor is failing it can cause the 5V level an issue. If 5V level is out of tolerance the...
  4. alldodge

    Engine starts and dies.

    I'm looking though them and compairing to the manual. Will get back with once my review is done
  5. alldodge

    4.3 tb IV no fire from coil

    Need to clean some connections. Start with the battery cables at both ends including the grounds
  6. alldodge

    Electric fuel pump issues

    The serial number 0L036613 0r 0L038613 comes up as 1998 3.0 If the motor coming with a mechanical pump and it was changed over to electric, it may not have the purple/yellow wire. Look on the solenoid to see where the wire would be and if there is even a terminal there This is how Merc would...
  7. alldodge

    Mercrusier 5.0 MPI (2008) RPM stops @ 3200.

    Have a motor serial number? Does the alarm work on the boat? Meaning do you get any beeps when the key is turned ON? If you do, check your fuel pressure at the rail
  8. alldodge

    '69 20' Bertram Sportsman Center Console

    The 470 is no longer made and many had their own issues. I would not fix the 470, just get something else. You did say you want to go back original though
  9. alldodge

    electric fuel pump problems

    Not an OB guy, but Merc uses the same wiring colors. Battery - Red After main engine breaker - Red/Purple Red/purple to ignition fuse (normally 20A) to key switch Key switch to Run circuit - Purple
  10. alldodge

    Engine starts and dies.

    The scanner shows readings from the sensors. The codes are also read by the scanner if there are any on another screen. If there are none, then I would think about having the ECM tested.
  11. alldodge

    Engine starts and dies.

    Things look OK, where there any codes?
  12. alldodge

    283 flywheel

    With the same part number they should both be the same. The difference in balancing holes most likely was better manufacturing processes for the newer one.
  13. alldodge

    Fuel gauge issues

    Need some clarification Merc uses Pink wire as the sender lead from the gauge Black is ground Normally Green is used as the bonding wire (which also goes to ground) but could be white Where does the Blue wire go to? The sender which was removed was a variable resistor type (240 ohms empty and...
  14. alldodge

    Electric fuel pump issues

    What's the serial number? I'm seeing the 1993 7.4 coming with a mechanical pump
  15. alldodge

    4.3L Volvo (starting out of the boat)

    It can be done with 2 jumpers at the 10 pin plug
  16. alldodge

    Random alarm 5.7L carb'd Bravo 2

    No, and your issue is intermittent so it is hard to find The switch can be below and behind the distributor
  17. alldodge

    4.3 GL Engine Mount Bolt replacement

    Being VP its probably metric Instead of chasing the threads could replace the bolt and nut with anything you want. Do recommend fine thread, but thats about it
  18. alldodge

    VP 5.0Gxi w/ SX-A on 2006 Four Winns H210 shakes when trimmed up

    Don't see the trim pump making the drive shake. Its just a hydraulic pump. With it on the trailer, put muffs on and run it in gear and watch as its trimmed up and down. If nothing is seen, I would take the drive off
  19. alldodge

    VP 5.0Gxi w/ SX-A on 2006 Four Winns H210 shakes when trimmed up

    Something is wrong and needs to be checked out. I would contact the folks who did the work Could be bearing was not installed correctly, U joints or coupler. The U joint should have been checked during bearing replacement, along with alignment
  20. alldodge

    Slack in DPS-A steering?

    Would be normal for cable steering
Top