Search results

  1. alldodge

    Random alarm 5.7L carb'd Bravo 2

    It may be a chafed wire. Power goes to the alarm and the Tan/Blue is grounded to sound the alarm. It can be the lube bottle, Temp sender and oil pressure switch. Check the oil pressure switch, it can be Tee'd with the oil pressure sensor which goes to the gauge. 87-864252A01
  2. alldodge

    Engine cut out while slowing down....

    Have been looking at parts from the old 140 to the new 3.0 and the studs, nuts, push rods have been all changed to the newer 3.0 Seeing a different cylinder head part number but that's about it @Bondo have any thoughts?
  3. alldodge

    Engine cut out while slowing down....

    The procedure above is also how the rockers should be tightened to spec. Manual states if not done this way it can bend push rods
  4. alldodge

    Engine cut out while slowing down....

    Agree Did you check clearance of the collapsed lifters? Basically the lifter is fully collapsed and tool is used to see if there is still room to insert the gauge. If its unable to insert then a different length of rod is needed
  5. alldodge

    Lost Propulsion! Need Help! Reply ASAP!!

    Wish you didn't say anything about getting your six pack If you had not said anything about the six pack the following would not have been typed: New boater Pull the boat and get it on the hard. Pull the drive and change the lube, split the drive and rebuild the water pump Pull the fuel...
  6. alldodge

    3.0 OMC 4cyl HELP!!!! SLOW CRANK BUT NO START

    That works, it came with a Holley 2V 2bbl carb Carb kit number 0986794
  7. alldodge

    3.0 OMC 4cyl HELP!!!! SLOW CRANK BUT NO START

    That number isn't coming up What year is it?
  8. alldodge

    3.0 OMC 4cyl HELP!!!! SLOW CRANK BUT NO START

    If it doesn't lock then the cable is broken or something is disconnected Most 3.0 used the holley 2bbl, or Rochester 2GC carb Only way to know for sure is if you can give us the serial number of the motor
  9. alldodge

    Riser Extension Blocks - Full Closed Cooling ???

    Cool beans
  10. alldodge

    New pistol for carry

    Big problem is how to get an auto to use rim fire Other then maybe lugar
  11. alldodge

    New pistol for carry

    Really, thanks My bad, your the best, always thought they were the same
  12. alldodge

    New pistol for carry

    I have a Kel Tec 380 and its a 6+1 Only good thing is its very small and light
  13. alldodge

    New pistol for carry

    Several make a 22 auto Tarus https://www.sportsmans.com/shooting-gear-gun-supplies/handguns/taurus-pt-22-poly-pistol/p/p47260 Beretta makes a 7 shot
  14. alldodge

    Cool Fuel Pressure Regulator - Testing

    A pump making "more" noise many times mean its sucking air or their is a restriction down stream, or the pump is worn Don't see a tank vent issue because it takes longer for that to show up Don't think you have a low pressure pump, but also don't know your serial number. It may have a boost...
  15. alldodge

    3.0 OMC 4cyl HELP!!!! SLOW CRANK BUT NO START

    Shift into forward and see if the prop locks in one direction, then shift to reverse and see if it also does it. That said, you should remove the drive, drain the gear lube and replace the impeller in the drive, and may need to rebuild the pump. Pressure test the drive after impeller...
  16. alldodge

    Can't seem to find a big enough fuse block

    Normally the 12V/120AC will automatically switch over to 12V when shore power is disconnected. That said there is usually a breaker on the 12V side, or could be a fuse and a switch. Might be the 12V line is not connected What size house bat does it have?
  17. alldodge

    3.0 OMC 4cyl HELP!!!! SLOW CRANK BUT NO START

    Remove all the lines and see if they need cleaning or replacement Can spray some carb cleaner thru the lines to help Remove the fuel filter and replace and clean it, but this depends on which filter is installed
  18. alldodge

    3 blade prop

    He does not want one to pull skiers The big IF If the PO change to 4-blade and did it right then they would have dropped 2 inches of pitch. Meaning if the boat came with a 3-blade 19, they would have gone to a 4-blade 17 If they didn't do it right, then it may be same pitch Hope someone...
  19. alldodge

    Engine starts and dies.

    OK, then need to start looking on the electrical side. The injectors are not being turned on/off ( Can you scan the the motor for codes? Can make up a scanner with a 12V resistor LED or use a digital multimeter that has a tone function if (Big IF) you have a MEFI ECM which looks like the one...
  20. alldodge

    3 blade prop

    Howdy Bob Keeping rpms low on the WOT side doesn't save gas or help the motor, it actually is worst on both To determine what pitch is needed we need some good numbers of what its doing now. What is current WOT RPM and loaded like normal? What is the speed at WOT using a GPS? What type and...
Top