Search results

  1. R

    ‘67 evinrude vs 19?? Johnson

    Lots of good used generators / voltage regulators can be found.-----Join-----aomci----And post wanted ad there.
  2. R

    Slide hammer puller

    There is not much load on the bearing carrier.----Those tabs hold it in position.-----No difference in pulling it out compared to any other carrier.
  3. R

    Slide hammer puller

    The propshaft bearing carrier simply pulls out with a slide hammer ( 1/4 threaded rod ) and will not damage bearings in any way !----Or 2 pieces of threaded rod and a strong back will do it.
  4. R

    Method to repair damaged crank/ flywheel key?

    The fitting of the key and the flywheel tapers is much misunderstood.-----Did a 50 HP motor a while back.----After talking to owner and some quick checks I suspected a sheared flywheel key.------Yes it was and and the tapers had been greased.----No wonder it sheared !
  5. R

    Reattaching an oil pump (and reservoir) too a 2004 Yamaha 50hp 3cyl 2 stroke?

    Motor will run just fine on 50:1 mix.----Plugs , on a motor in good condition do not foul with a 50:1 mix ratio.------But oil / lubrication on 2 strokes is not well understood in my opinion.----Model # of your motor ?
  6. R

    Method to repair damaged crank/ flywheel key?

    Facts.------The key locates the flywheel for proper timing of the MAGNETO.-----The flywheel is driven by the locking tapers.-----Flywheel tapers must be lapped for proper fit contact.---Must be installed clean and dry.------Nut must be torqued to specification.-----So get a new factory key and...
  7. R

    ‘67 evinrude vs 19?? Johnson

    I think you will find that the brackets are the same !!
  8. R

    ‘67 evinrude vs 19?? Johnson

    The 62 to 64 model 28 HP----1965 to 70 model 33 HP----1960 a to 76 model. 40 HP----Your location ?
  9. R

    Help with my 125

    That is the correct part.
  10. R

    Evinrude tell tail not discharging

    A new purchase needs a new impeller !
  11. R

    Too windy?

    About 20 minutes.----Boat was a Contessa 32 , these were studied after the 1979 Fastnet race as none sustained any damage.-------Quite scary when you do not know what the next gust is going to do.------On shore there were pine trees snapped like match sticks. broken 20' above the ground where...
  12. R

    Help with my 125

    I worked at a dealer when those motors were NEW.------I know what they look like.-----Where did you get your parts ?----Off of what motor and what did the parts look like.----Pictures from you.----I do not know how to post pictures.----Don't want to learn either.
  13. R

    87 120 - vro removed, use premix, low-end rough - high-end precise & responsive

    Post your compression numbers first.
  14. R

    Need help with 1968 1.5 HP Johnson model SC-10S

    I think I see the 2 timing marks on the magplate in the middle picture.-----Hint, the timing narks do not look like what you find on a 57 chevy like grandpa had.
  15. R

    Help with my 125

    Pictures or part numbers of the " wrong " parts ?-----And where did you get those parts ??
  16. R

    1978 70 hp Johnson throttle problem

    From where I sit it sounds like everything is working as designed.-----Get the manual.----Read it before opening your tool box to work on these simple carburetors !
  17. R

    Need help with 1968 1.5 HP Johnson model SC-10S

    It does have timing marks.----You are stubborn and don't want to look for them -----On the magplate and one notch on the flywheel !
  18. R

    Yamaha 115 4stroke

    Yes ---Sellers sometimes confuse 4 cylinder with 4 stroke.----Public perception is that 2 strokes are an inferior engine.----And 4 strokes are much easier to sell.----Many buyers have no clue as to how to spot / tell the difference either.
  19. R

    Need help with 1968 1.5 HP Johnson model SC-10S

    You set the HIGH speed mixture at full throttle.-----Then slow the motor to idle for setting the low speed mixture.
  20. R

    Need help with 1968 1.5 HP Johnson model SC-10S

    You are saying it can't be done ???-----Wait wait.----Get the battery from your riding lawn mower.----Hook up the timing light.-----Observe the flashing of the light .----And you can find the timing mark on the magneto plate as well.-----Should fire between those 2 vertical lines all the...
Top