Search results

  1. alldodge

    MCM 5.0L EFI 305 Will not Start.. Fuel Starvation? Cool Fuel Gen II? (FIXED ISSUE!!!) Fuel Pump replacement

    The beep should do it 5 times then stop for low fuel pressure. My guess is you have the issue, just need to find out what part is keeping the pressure low, pump, regulator, injectors or something else
  2. alldodge

    Delco Voyager marine ignition system

    The way I see the issue it comes down to money. Replacing a TB4 or 5 module cost quite a bit. Most don't want to drop 4 to 500 on a new module so the EST is less costly alternative. The timing curve is different and going to EST will change your performance. Just comes down to cost
  3. alldodge

    3.0L to 4.3L mtr mounts and 25 yo transom

    I would suggest a minimum repair of lines in Green, or up to the Red top. Cut into the stringers and glass them back in when done
  4. alldodge

    Changing drive

    I don't know what prop pitch or drive ratio your using so I plugged in some numbers based on some assumptions. Here is a link to bblades prop calculator http://bblades.com/propeller-slip-calculator/ So using the numbers mentioned above it comes out to 36%
  5. alldodge

    Chrylser 105 Conqurer

    Laid the plywood, screwed to the stringers, put in 6 inch tabbing down all side, then laid full layer of CSM and poly. Used up a bit over 4 gallons of poly and appears I'm going to need some more.
  6. alldodge

    MCM 5.0L EFI 305 Will not Start.. Fuel Starvation? Cool Fuel Gen II? (FIXED ISSUE!!!) Fuel Pump replacement

    You don't have a carb with a float bowl, you have a Throttle body with two injectors installed on top of it. Should look something like this Here is how the system fuel flow works
  7. alldodge

    3.0L to 4.3L mtr mounts and 25 yo transom

    I see there is more of an issue here, what about this method. Bolt can be raised up some also
  8. alldodge

    ***Alternator mesurements for 3.7 Mercruiser mod**Not much room in engine bay**

    This should help, ALT is 5.6 inch wide, so I will guess it's 3.5 to 4 inch away
  9. alldodge

    3.0L to 4.3L mtr mounts and 25 yo transom

    The bolts go completely thru the stringers. Glass and cloth is laid and finished, If necessary sand the one side area where the aluminum 3 inch angle sits against the stringer. Then drill thru the aluminum angle and stringer. Use sealant in holes and put bolts clear thru and secure on the other...
  10. alldodge

    89 3.0 w/ est distributor

    There is a gray wire going to pin 2 on the engine harness connector. This wire goes to the tach, disconnect the wire at the tach and see if you get spark. If still no spark remove connector at the coil and measure resistance from the tack wire to a good ground, it should be infinity.
  11. alldodge

    72 Thunderbird Formula w/twin 165hp Mercs

    Then the one WOG posted will work. It uses a manual switch to put the two together when needed. The combining switch can also be done using a solenoid so you can just push a button at the helm. Run the house wiring off one of the batteries using the 10 AWG wire (shown).
  12. alldodge

    New guy here with a boat/motor swap situation NEED advise/help/info PLEASE THANK YOU

    Guess need to ask the OMC folks to see if the OMC hole is the same size or larger then the Merc. Here is Merc I found this but do dimensions Best if posted in the OMC section since going from Merc to OMC
  13. alldodge

    Crownlne 2005 270cr Questions

    The beep is normal and tells you your computer is working, it will continue until the engine is started. If it goes off with the engine running you have a problem. If it ever goes off and is a solid sounding beep, its either lost oil pressure, drive lube is empty or engine is over heated. Two...
  14. alldodge

    transom question on zinc anodes

    We canot see what your seeing due to we have to be a member of ifish. You need to pot 2 more times to be able to upload pics. So post two more times then either use the direct link or upload
  15. alldodge

    Hot wiring a 3.0 on the garage floor

    Put a jumper between pins 5 and 6 on the engine connector. Red/Purple to Purple
  16. alldodge

    Formula 27PC Complete Power plant rebuild

    Pulled the boat out today and winterized. Here you see a strength edge with the transom and it's right where it should be from my point of view Here is the hook, first I thought it went across the hull but the only hook is just on the outer 12 inches of the hull and just in front of the tabs...
  17. alldodge

    5.7 Bravo Winterization

    You should have power steering oil cooler unless yours is an inboard. If it is an inboard and have full hydraulic steering, there will just be a tube where the power steering cooler would be. Don't bother with the Thermostat
  18. alldodge

    Help with part number

    Looks to be a CA 27319 adapter kit, or a Teleflex adapter (probably made for Merc) see list below...
  19. alldodge

    Bravo Drive Bellow installation

    Here is what it should look like
  20. alldodge

    Boat too heavy

    I'm assuming funds are limited so the reason for trying this, other wise could call a hauler. Going to try a different approach, this will stand a better chance if you can make some bunks. This still is iffy but should work if its built right. At least a 20 ft trailer, longer is better Can...
View older results
Top