Search results

  1. zarillus

    OMC Shift cables backwards??

    On a standard 1986 OMC side mount shifter does it matter which cable is for the throttle and which one goes to the shifter?
  2. zarillus

    Need major help new float on trailer

    Got a new trailer, my boat is 1967 Larson about 17 ft and 16ft from transom to bow eye and i will be putting it on a 20ft v galvanized Trailer.I want to know what y'all think about the bunks.I want all bunks and on the new trailer they are about 20 inches apart however that would not support my...
  3. zarillus

    Occasional beep what is going on

    110HP Evinrude 89 Occasional beep when first starting up first few minutes then okay??
  4. zarillus

    Recommended trailer for Old BOat

    Need recommendations on a new trailer to replace my old original gator trailer.My boat is a 1967 Larson All-American 166 and the current boat trailer is just too hard to load.I am looking for a drive on, the boat has a deep v and i want it to sit nice and low in the trailer.Anyone have any...
  5. zarillus

    When loading trailer the KEEL keeps hitting the frame!!

    Guys, Have an old 67 larson with old gator trailer ,Not sure how to remedy this,maybe i am just not backing the trailer in far enough in the water,however everytime i load it i am slamming the keel right into the damn square frame like where you woul dbolt your license plate too. Before it...
  6. zarillus

    1989 Evinrude 110hp 20" shaft reverse clunk?? Shift rod adjustment or ??

    Hi Guys, I have been searching the forum and i have seen many posts regarding shift rod height. When i put my motor in reverse it clunks before going into gear wether i shift it slowly or fast.My question is there a cable adjustment i can make? The shift rod height is in spec for my motor, so i...
  7. zarillus

    Outboard mounting height too High?? Older larson with new motor

    :confused:Guys-I have a 67 Larson All-American 16ft with an 20 inch 89 110hp evinrude.I am trying to figure out the proper mounting height.When i took it for a lake test it seemed very unstable at high speed.Sorts like driving an old Ford pickup with bad ball joints on the freeway.Hard to...
  8. zarillus

    OMC Fast Idle lever keeps popping up?? After shifting won't return to idle? Related?

    Kind of a two part question: Hope someone can help me out, i just replaced the two cables on my 89 evinrude 110hp with standard omc side mount shifter.For some reason my fast idle lever keeps popping up when i shift into forward it also does this in reverse?? I don't know if its related...
  9. zarillus

    Don't want to scrape up my KEEL? HELP?

    Need some Advice on what i need to do so that the boat does not scrape the cross member on old gator trailer.The gator trailer is the original to the boat a 1967 Larson All-American.It is also a tilt trailer with a pin if that helps.Anyways what should i do here? Raise the front bunk support...
  10. zarillus

    +12v from the Ignition switch to gauges or BATT power??

    I am re-wiring my entire boat with new gauges and switches.I have an OMC remote control with power tilt.I saw the generic wiring diagram and it said to use the Ignition wire so my gauges are not always on.Well my ignition is inside the control box so how am i supposed to wire it that way...
  11. zarillus

    Help me identify these WIRES ?????????

    I just got an OMC control box for my 110 Evinrude and have some additonal wires i need help identifying.I have the big red plug which goes to the engine that wasnt too hard.However i also received two sets of wires one with a spade plug and one with a 5 pin round connector and a white box...
  12. zarillus

    Old Evinrude vs Newer Evinrude Motor Height?????

    :( :(:(:(:( I am finally installing my new motor on my 67 Larson which has a 20 inch transom.It originally had a 20 inch 67 85 hp fat 4 and i am installing a 20 inch 1989 110hp.The old motor was mounted on the transom and it seems that the motor sat really low in the water compared to newer...
  13. zarillus

    Thoughts on a 86 sea ray seville? Are these decent boats?

    :confused:Looking at my first I/O wanted to get your thoughts.The boat is a 1986 18 ft Sea Ray Seville 170hp mercruiser.Boat runs well and top speed is around 45 mph? Things i should check on this paticular model? Thanks in Advance:confused:
  14. zarillus

    Opinions wanted on new OB for my 67 Larson all-american 166

    Guys-Looking for a 20 inch motor for my 67 Larson for around $2500.00.I need recommendations on Year and HP.I need something easy to work and is not touchy as far as maintenance and adjustments go. Thx in Advance
  15. zarillus

    Need opinions on new motor for my old Larson want to spend around 2500.00/ HP?/YEAR?

    :(:confused: I have been looking at all types of motors and i am conflicted i have about 2500.00 to spend and i need something solid.Not looking for a touchy motor just a good workhorse 2 stroke. I am thinking like 80's evinrude, 115 ?? I don't know i neeed something that's easy to work and...
  16. zarillus

    IS 150HP Johnson too much for my boat??? Should i be looking at a 90 or 115?

    :confused: Long time since i have been here.I am wrapping up my boat project and i am getting ready to buy a motor and saw a good deal on a 93 Johnson 150 HP motor.My boat is a 67 Larson all-american 166 16ft boat.I am not sure what the max hp is however my new transom is nearly two and 1/2...
  17. zarillus

    Best Used motors?? $1000-$1500 80-150HP 20 inch shaft ????

    Guys- Need a new motor want to spend between $1000-$1500 what are the best types of motors out there in that range? Early-Mid eighties Johnson? Early-Mid eighties Evinrude? Early nineties? What do you guys think?
  18. zarillus

    67 Larson American--Weird rubber in KEEL?

    Guys, i have a preety bad shaved keel which takes on water and while sanding it and getting it ready for repair i noticed a black rubber like substance just before i hit fiberglass.Does anybody know what this is? It doesn't look like a Keel guard just part of the very bottom of the keel. Did...
  19. zarillus

    Fiberglass.....Fiberglass..... Fiberglass....

    :confused:I sooooo freaking confused now!!!!! We need a forum for just fiberglassing.One for poly guys and one for epoxy guys.There is so much info that the average newbie like myself... gets all confused!!! 1708,cloth,mat,roven,hexcel,carbon fiber,kevlar.Poly,vinlyester,isopthlathic,epoxy...
  20. zarillus

    Stringer idea whatta you think???

    Well i think my posts are getting lost in the masses so hear is a fresh one.It's my stringer idea.Feel free to comment would like to get input.Attached photo
Top