Search results

  1. jerryjerry05

    I'm stumped, please help. 1996 40HP force outboard

    If the bottom cylinder works?? The fuel pump is operated from the top cyl. Check the pump and see if the diaphragm is bad???
  2. jerryjerry05

    85 hp force shift coupling assembly reinstall

    I'm pretty sure Frank would like the accolades. But Frank passed a few years ago :( He was one of the best and went way too early. And thank You.
  3. jerryjerry05

    1986 85hp force 856X6L no spark

    http://www.outboardignition.com/. The Prestolite stator is probably the OEM No fire on any cylinder: 1. Check the resistance from each blue to the yellow wires, you should read approximately 300 ohms. 2. Check the resistance from each blue and yellow wires to engine ground, you should read...
  4. jerryjerry05

    85 hp force shift coupling assembly reinstall

    timbramo: you have a question or just want to share Franks wisdom and expertise ?? Jerry
  5. jerryjerry05

    Sneezing from underneath flywheel

    You sure it's coming from under the flywheel? Looks like it might be from the top port cover and not the flywheel???? On the top carb: where's the air screw set at? Under the pack(never saw one that looks like that) the top port cover(1 of 3) might have a blown gasket?? The gasket is thin and...
  6. jerryjerry05

    Tillotson TC-5E float needle valve

    If it's running but running bad?? do the starting fluid test. Start and run at idle, spray SF around the intake side of the motor. Spray under the base of the carbs and under the pack/coils and around the 4 port covers, anywhere it might draw air into the motor. IF??? it makes the motor run/...
  7. jerryjerry05

    Sea-king Chrysler 15hp outboard motor does not start

    If you have fuel coming out the exhaust snout?? Then you have put too much in or the fuel pump is defective.
  8. jerryjerry05

    Tillotson TC-5E float needle valve

    Years ago the factory service dept. issued a service bulletin. They suggested/said "set the air screws out at 1 turn and leave it there" I've never found that that would work. I had 4 1988 85hp and all liked the 1 and 1/8th turn out.
  9. jerryjerry05

    Sealant for gearcase drive shaft and gear housing cap Shift shaft

    Just about anything you use will be ok. I use the High Tack. Google "gasket sealers" a bunch of them show. The first one is the old OMC sealer. I prefer that but thought it wasn't available???
  10. jerryjerry05

    1989 85hp force won’t start

    The idle is set using the towershaft linkage. The "idle screws" are for the air/fuel mix at slow speed. The air screws are usually set at 1 to 1 1/8 turn out. Most will run at that setting, but some need to be set more open than that. One customer had his set at 3 turns out??? A "kick" or...
  11. jerryjerry05

    1995 Force 120 will no longer idle

    The buzzer shouldn't sound when starting. Only when 12v is applied. If it buzzes when 12v is applied?? then it's doing the right thing. Should only sound when voltage is sent to it.
  12. jerryjerry05

    Tillotson TC-5E float needle valve

    Going down too far in jets can cause a bunch of trouble. Running too lean,can make it run too hot and that can cause it to burn holes in the top of the pistons( did that on a motorcycle back in 1972, burned a 150$ hole in a piston. $150 in 1972 was a BUNCH of $$$.
  13. jerryjerry05

    Tillotson TC-5E float needle valve

    You have the old parts, I have a bunch of New/old stock needles/jets? Take a couple of pics next to a ruler I might have something that will fit??
  14. jerryjerry05

    Sea-king Chrysler 15hp outboard motor does not start

    "spark looks good to you" ?? How did you test it? If you squeeze the ball and pump the bowl full that should be enough fuel to start the motor. You using the choke?
  15. jerryjerry05

    1995 Force 120 will no longer idle

    YEA!!! sounds like your getting there. Another test: run the motor and get it hot, then running at full throttle turn the key off, don't throttle back just kill the motor, then pull the plugs and check the burn. Check for all 4 plugs being the same burn.
  16. jerryjerry05

    Tillotson TC-5E float needle valve

    Granger might have needles?? Could this lead to a generally rich mixture and chronic fouling of plugs in a short period of time? Yes. It will allow excess fuel and make it run bad.
  17. jerryjerry05

    1995 Force 120 will no longer idle

    NOT IDLE screws. while they will affect the idle thats not what they're for. They're for air/fuel mix at low rpms. The idle screw is on the towershaft. Set the air screws at 1 and 1/8th turn out. Then adjust from there. Once you get it running, do the starting fluid test. Start the motor, spray...
  18. jerryjerry05

    Tillotson TC-5E float needle valve

    If the needle is all metal and no rubber in the seat?? then the carb will leak fuel. IF?? the seat has the rubber in it, then be careful what cleaners and soaks and additives you use, as the seat can swell shutting off the flow. If it swells? rinse in soapy water and let air dry. The...
  19. jerryjerry05

    Best 2 stroke oil for Chrysler / Force outboards

    Seafoam's a JOKE!!! The very best oil is Amsoil, also the most expensive. I had a pair of 1988 Force 85hp. used them for over 30 years. They were new and before TCW-3 the oils produced were purposely made to carbon up, both motors the rings carboned up. I caught them before the motors got...
  20. jerryjerry05

    1995 Force 120 will no longer idle

    Good find!! The reeds can actually be opened a tiny bit and not affect performance. But missing that's not good.
Top