Search results

  1. S

    Check/Fix/Replace Starter Motor 1996 50hp

    A little confused about your terminology, but the kill system can test good (continuity wise) but still fail under full load. Everything hooked up completely right that is. Something is robbing power.
  2. S

    Check/Fix/Replace Starter Motor 1996 50hp

    I was just looking through the eyes of an inexperienced or super busy op....compared to many starters it's not AS easy. Simple tool is easy to make.
  3. S

    Check/Fix/Replace Starter Motor 1996 50hp

    Agreed, starter is pretty easy to test and cleanup. Installing the brushes is the hardest part but doable. While spinning and under load, that starter should read 10.5 volts or so. I assume you have bench tested the starter on the outboard....(By passed some electrical components) ?
  4. S

    trying to install a pre-owned PTT to a1996 Johnson 50

    You can just buy the handle trim assembly online or used. There's plenty out there or go to one on the dash. I've always gone with the throttle one though, safer and more effective.
  5. S

    Water pressure valve replacement 2000 evinrude 4stroke

    This should help
  6. S

    Water pressure valve replacement 2000 evinrude 4stroke

    Parts 5, 6 and 7 will give you "the glory" but like everyone says....you need nothing. Follow the yellow brick road and get what the scarecrow needed. 🤓
  7. S

    Water pressure valve replacement 2000 evinrude 4stroke

    I'd say it's above like it's supposed to be. Step back and take another picture.
  8. S

    Water pressure valve replacement 2000 evinrude 4stroke

    Picture of where it is or where you think it is. Picture worth a thousand words or video worth a billion.
  9. S

    Water pressure valve replacement 2000 evinrude 4stroke

    So this should be the assembly, and where does this go on the block?
  10. S

    Water pressure valve replacement 2000 evinrude 4stroke

    I'd leave it alone and test. Run some mild soap or something. Impeller yes, stats? No. I don't work on those motors but I've never seen a design where you don't have access to areas.
  11. S

    Water pressure valve replacement 2000 evinrude 4stroke

    Saltwater motor?
  12. S

    Lubricate new water impeller rubber ?

    I throw a little dish soap in there but it's not necessary. Who wins? Are you eating crow or your buddies? 🤗
  13. S

    67 Year Old Head Bolts

    Me and two buddies are going to buy tw200 made by Yamaha. Quite a following. If you're referring to the net I just take a little screwdriver and hold on there while I probably inside otherwise you're probably talking about everybody's super Goo and again the crayons work the best in my humble...
  14. S

    67 Year Old Head Bolts

    Brutal? They were fun, until they weren't!
  15. S

    67 Year Old Head Bolts

    I raced two stroke dirt bikes, YZ 400 was my last full on one ... We had the little cable clamps with the little WD-40 hole for the tube. Pulling outboard bolts has been fairly easy to me.. now... that I have failed many many times! 🤓
  16. S

    67 Year Old Head Bolts

    No, it will not work.
  17. S

    67 Year Old Head Bolts

    Yeah colored crayons discolor the paint for sure, I just use light or dark depending on the motor so white on white and the darker on the darker.
  18. S

    67 Year Old Head Bolts

    I use map gas and go forever....sometimes the original OMC paint doesn't even show much harm amazing stuff. Acetylene, map gas I've used them all. Map gas or an induction here is all you need that in a few crayons.
  19. S

    1977 70 hp johnson thermostat housing gasket

    I pull my thermo stats out every year and soak them in salt away. Keeps everything nice but I'm saltchu.... I talk to myself all the time when I'm working on stuff....deeply into it. But I don't write to myself usually. Pretty intense stuff.
  20. S

    67 Year Old Head Bolts

    Corrosion and rust from age or abuse really. You have a tough project ahead of you. I purchased an inexpensive 120 volt stick welder just for removing said bolts. Stainless stick rod, stainless nut and I drop it in the middle and puddle it in. Takes some practice but works very well. Looking...
Top