Search results

  1. A

    First Tohatsu motor 9.9HP

    The old boy is smoking again! But, now the issue is to adjust it to run smoothly. I really need help with following: I adjusted linkage as per manual (+3 degrees fully closed to +22 degrees fully open), but I rebuild the carb and can not find details on how to adjust it properly. Manual says...
  2. A

    First Tohatsu motor 9.9HP

    Funny, just got reply from CDI that they can repair trigger coil for $113 + shipping...
  3. A

    First Tohatsu motor 9.9HP

    I was told by the vendor that this trigger coil will not work. CDI did not respond to my request. But, I just got on Ebay the whole ignition (plate , exciter, trigger, charging coils, CD unit and ignition coil with all the wires) for less than I paid just for new CD. And CD unit and the rest...
  4. A

    First Tohatsu motor 9.9HP

    I went thru test sequence again for exciter and trigger and exciter passes test again, but trigger shows infinity instead of 30-60 Ohm and no DVA output. I wonder if I can find original one to replace or use the one above...
  5. A

    First Tohatsu motor 9.9HP

    I am back to this slow running project. Neither new ignition coil, nor new CD unit brought sparks back. It took me some effort and "redneack ingenuity" to get fly wheel off. Man, it was stuck really hard and having left-hand thread ( as it turned out) did not help either. Not too many things...
  6. A

    First Tohatsu motor 9.9HP

    One single that goes to coils primary wiring (right). One single that grounds to the holding bolt (second from right). One triple that goes under flywheel (third from right). One double that goes to shut-off switch. (left one).
  7. A

    First Tohatsu motor 9.9HP

    here it is
  8. A

    First Tohatsu motor 9.9HP

    Just got reply from CDI that they are not aware of any replacement CD for my motor. Interesting. All parts sellers show part# 362060601M (available) as replacement for my part# 362060601 (not available) . I even found instructions on marineengine.com how to change three-prong connector I have...
  9. A

    Need advise on MG Tracker 34 PRO trolling motor

    Eventually got contact plate glued together piece by piece. Glued magnets in S-N-S-N order. Motor runs! But two issues: 1. Runs in opposite directions (reverse). Not sure if I have to re-glue magnets shifting them from S-N-S-N to N-S-N-S (90 degrees shift of magnets) or just switch black and red...
  10. A

    First Tohatsu motor 9.9HP

    Test for CDI is done when it is actually all connected and motor is cranked. Is there other way to test it like for exciter and pulser when you disconnect it and measure resistance?
  11. A

    First Tohatsu motor 9.9HP

    Just saw your new reply. I will try to contact CDI.
  12. A

    First Tohatsu motor 9.9HP

    I wish I knew it before test... I did not see anything in the manual. New tester has 3V. Analog tester has 1.5V. But, cheap digital had 9V. On another hand since there was no spark something had to be wrong before test. It could be CD. Do you know if CD in the link above fits? It looks very...
  13. A

    First Tohatsu motor 9.9HP

    Web search for 362060601 pulled a few replacement CDIs that look different from mine varying from $151 to $190 (pricy!). All look like that: https://www.boatersland.com/cdi-119-0602-ignition-modul-tht362060601m.html Will they work?
  14. A

    First Tohatsu motor 9.9HP

    Exciter passed the test. Pulser 90% passed. CD did not. Is there a chance to get CD for this or adapt some other CD unit?
  15. A

    First Tohatsu motor 9.9HP

    From my picture you can see that manual says it is only 4K and my multimeter is on 20K scale. I think it should work... Pulser did pass the book test, but exciter and CD unit did not. But , I did get strange readings. I will get from my friend electrician high-end multimeter ( honestly my units...
  16. A

    First Tohatsu motor 9.9HP

    Finally got new coil (took forever to get). Put it on - no spark. I took it off and run manual recommended tests. It measured 0.2 Ohm on primary winding (the same as old one) and NO CONTINUITY on secondary (the same as old one!) while manual says it has to be 4.1-6.1 KOhm. Did I get bad new...
  17. A

    1968 6 HP Evinrude need help

    Got the carb. Washed\cleaned it, put new ref kit, put it on motor. Bingo!!! Motor runs like swiss watch! With all new ignition and fuels systems I just need to put new impeller and I have new motor. :) I would never figure that carb is incorrect without help of people on this board. Thank you...
  18. A

    Need advise on MG Tracker 34 PRO trolling motor

    I was able to remove all magnets (it was hard). I tested polarity with compass and they are not the same. There are two pairs of opposite polarities. S an N is not on the ends , they are on large curved sides of the magnets ( see pics), so direction of the magnet should not matter . but position...
  19. A

    Need advise on MG Tracker 34 PRO trolling motor

    .
  20. A

    Need advise on MG Tracker 34 PRO trolling motor

    Yes, that was what I really wanted to do, but I was not able to determine direction of polarity without taking magnets off. I tried to heat JBWeld using gas torch from outside of the housing and punch magnet out using piece of wood. I was able to get out one magnet so far with just a small...
Top