Search results

  1. C

    1962 evinrude fastwin 15036 fuel issue

    I filled the tank up this morning and bulb is staying firm and it's running great again.I believe some low life stole it.At least he didn't cut the line and steal the tank .That happened one time.Anouther time they got it out of my bay boat.The cap was left off and before I found it rain got...
  2. C

    My new project.1972 johnson 25e72r .

    There was no plastic retainer but a thick fibrous material.Looked like the same stuff as the old packing washers but thicker one piece.My 71 20 hp parts motor had the same material in it and no retainer
  3. C

    1962 evinrude fastwin 15036 fuel issue

    I have been posting about this motor lately.I had it running great.I have had it in the drum cranking it for 5 days.This morning it was hard to start and not running right.I checked the bulb and it would not stay firm.I then checked the tank and it was almost out of fuel.Its a 3 gallon tank...
  4. C

    My new project.1972 johnson 25e72r .

    Good to know I'll make sure I never swap those
  5. C

    My new project.1972 johnson 25e72r .

    This motor ran 3 years ago.I used it a long time.When cleaning the carb 2 screws that hold the bottom bowl on were gone .Both on the same side.I have a 71 20 hp that is basically the same looks wise .I robbed 2 screws out of this bowl.The carbs looked the same.What is the difference The carb...
  6. C

    1962 evinrude fatwin 18hp carb settings.

    I got her going she is shifting ,peeing and cranking great .Thanks everyone for the great help
  7. C

    Evinrude 1972 18 hp fastwin not pumping much water

    I got her running in the barrel. I think the pump housing grommet was the issue she is now peeing and appears to be cranking and idling great thanks for the help
  8. C

    Evinrude 1972 18 hp fastwin not pumping much water

    I wish I had seen the pictures before I put it back together.I did not check those holes
  9. C

    Evinrude 1972 18 hp fastwin not pumping much water

    15036 best I can tell ITS A 62 or 63.i blowed air. through the water tube and air was coming out of the exhaust holes.Something did come out of the exhaust holes.I reinspected the pump assembly and found no problem .Then I tried to crank it and it would not crank.I checked spark with a tester...
  10. C

    Evinrude 1972 18 hp fastwin not pumping much water

    I just got this running . I put a new impeller in it.it is pumping a little water but not much.I think there was a rubber boot that the water pump tube slid into that if I remember correctly did not look right.I am going up to the shop to remove the foot.Do I need to blow compressed air in the...
  11. C

    1962 evinrude fatwin 18hp carb settings.

    I set points at 20 but ordered a coil gap tool and an ignition timing tool so I can get it right
  12. C

    1962 evinrude fatwin 18hp carb settings.

    I don't see any cracks in the coils.One coil does look newer.I sanded the contacts with 150 grit and sprayed carb cleaner.I don't know enough about points to tell if they were good are not.I gaped them at 20.Do I need to replace the condensers?Do I need to lightly sand the flywheel contacts on...
  13. C

    1962 evinrude fatwin 18hp carb settings.

    I don't see any cracks in the coils.One coil does look newer.I sanded the contacts with 150 grit and sprayed carb cleaner.I don't know enough about points to tell if they were good are not.I gaped them at 20.Do I need to replace the condensers?Do I need to lightly sand the flywheel contacts on...
  14. C

    1962 evinrude fatwin 18hp carb settings.

  15. C

    1962 evinrude fatwin 18hp carb settings.

    112 both cylinders
  16. C

    1962 evinrude fatwin 18hp carb settings.

    112 both cylinders
  17. C

    1962 evinrude fatwin 18hp carb settings.

    What is the best way to get the flywheel off.I know it usually requires a special tool.will screwdrivers and a maiiet work.Do you have to take the 4 screws off holding the plate on top of the flywheel
  18. C

    1962 evinrude fatwin 18hp carb settings.

    The carb looked good inside no varnish or crud .I got a kit anyway
  19. C

    1962 evinrude fatwin 18hp carb settings.

    I ment to say the foot oil had no water in it
  20. C

    1962 evinrude fatwin 18hp carb settings.

    You are right I was looking at the choke knob.I had a brain fart
Top