Search results

  1. J

    1977 Mercury 110 9.8 compatable lower units

    Are there compatable lower units which will fit a 1977 Mercury 110 9.8 motor?
  2. J

    1977 Mercury 110 9.8 HP no spark

    I got this motor at a auction. The toe on the lower unit, which protects the prop, has been broken off. but the lower unit is sold. The motor appears it has been used very little. I took out the sparkplugs and they are new, no signs of use. Problem is I have no spark. The kill switch wires...
  3. J

    Change Prop Hub from Yamaha to Johnson

    I have a prop I got at an auction which is a 335933 (13 1/8 x21) . It has 15 spines How do I get this to fit a Johnson 65 hp? Also it has a chip about 1/4 x 1/8 will that have to be repaired, if so who can do that. Local machine shop?
  4. J

    Overheating 1977 Evinrude 85HP

    I put in a new water pump about 3 weeks ago. It ran okay and the cylinders were cool to the touch after serveral minutes. I changed to a new prop from a 13x19 to 13 3/8 x 17 to get out of the hole better to pull grandkids. This may not have caused the problem. First day out ran great. Second...
  5. J

    85HP - 1977 Proper PROP for getting out of the "hole"

    I have a 1977 85HP which has a 13 1/4 x 19 prop. I bought it about 6 mo ago so know little about the performance. I took out the grandkids to pull on a tube behind the boat and it is very slow getting out of the "hole". Runs like a "scalded dog" after it gets up on top. Now they are wanting...
  6. J

    85HP - 1977 Proper PROP for getting out of the "hole"

    I have a 1977 85HP which has a 13 1/4 x 19 prop. I bought it about 6 mo ago so know little about the performance. I took out the grandkids to pull on a tube behind the boat and it is very slow getting out of the "hole". Runs like a "scalded dog" after it gets up on top. Now they are wanting...
  7. J

    Loss of Power 1977-85HP Evinrude

    I cleaned out my carburetors last week and had my engine running great. It would pull back the skin on my cheeks. I took the grandkids out today and it had no power. It would start, put when I shoved down the throtle it would not go any faster. I had two small boys and a girl in the boat. Not...
  8. J

    Rebuild 1977-85hp carburetor

    I have a 1977 Evinrude 85hp motor I just bought. I replaced the fuel pump cleaned out the carburetor and let Seafoam set in it overnight. and now it runs like a "scaulded dog" with the water mufflers. I siphoned out the gas and put in fresh gas with Seafoam and let it run for 15 min while I...
  9. J

    20hp Johnson starter motor drive gear will not go back back down after it starts

    I have a 1969 20hp Johnson. I installed an electric start motor on it. Now the drive gear on the motor will not go all the way back down. I took a screwdriver and held the gear down to keep the teeth from hitting when it was running. I sprayed with WD40 and worked the drive gear on the motor...
  10. J

    Test Electrical System Electrical start 9.8 Mercury 1983

    I have a 1983 Mercury. When I hold the sparkplug and hit the start, I don't see or feel any spark. Where do I start to test where the problem is. I looked under the flywheel but did not see anything unusual. I see the two coils and looks like an electrical box with wires coming out but don't...
  11. J

    AGE of 9.8 Mercury Serial Nuber 630613 Blue strip

    I have a 9.8 Mercury with a Serial number of 630613. What Year Model is it?
  12. J

    Age of 9.9 Mercury 0b126071

    What is the age of Mercury 9.9 0b126071?
  13. J

    Correct Rebuilt 1972 1972 9.5HP 18-7823 fuel pump

    I followed the instructions at http://www.sschapterpsa.com/ramblings/Rebuilding_fuelpump.htm But when I finished I cannot blow thru either of the spouts. I rotated the outer gas imput 1/4 turn and I can blow thru both. But can't get the right combination blow thru input but not back thru output.
  14. J

    9.5 Evinrude Runs then Stops Gas problem

    I have a 1972 Evinrude when I spray WD-40 in the car, it starts but stopes in about 15-30 seconds. I rebuilt the fuel pump. How do I test it. If I disconect from the car and the spray WD40 into the car, should I see a constant stream of gas coming out the disconnected hose? There is presure...
  15. J

    Back Flush 1977 Evinrude 85hp

    I have my lower unit off the motor and I read you should back flush the motor since I have it off. How do I do that?
  16. J

    Lower Unit Linkage for 1977 Evinrude 85hp 85799S ..need to remove lower unit

    I am wanting to replace the waterpump on my 1977 Evinrude 85HP. I have removed the 5 bottom screws but the linkage is holding it from releasing. Where is the linkage located and what should I watch out for. Any suggestions would help.
  17. J

    1977-85hp Evinrude Carburetor adjustment screws

    Where are the carburetor adjustment screws located on a 1977-85hp Evinrude? Most I have seen in the past are brass. I don't see any brass screws on any of the four. Is it under the screw in the attached picture?
  18. J

    Should the 1977 Carburetor drain when drain plug removed?

    I have a 1977 -85hp Evinrude. I removed the drain plug from the bottom of the carburetors and pumped the bulb. Three of four did nothing the other one gas came out. Do I have a problem with the one or three?
  19. J

    Tune up 1977 Lower Unit Metal Filings on drain plug

    I have a 1977, 85 hp Evinrude motor. I was following the instructions on tune up of an unknown motor. I drained the lower unit oil and thought there was grease on the lower plug, but it is metal filings attached to the magnet. The picture shows them to be larger than they are. They all are just...
  20. J

    How to Test coils on 1972 9.5 Evinrude

    I followed the suggestions on another post to test the electrical system. I got lost in some of the checking of ohms on the coils. I did a test by holding the spark plug and got a jolt on one but nothing on the other. To test the coil with an ohms meter, what wires should I do the test on? The...
Top