Search results

  1. Lancer76

    Melted coil feed wire = Bad Pertronix?

    Ford 351W (Mercruiser 233). Been slowly chasing down some starting/wiring issues. Present head scratcher is that when I apply 12 V to the coil via the electric choke, the wire from the choke to the positive on the coil got hot enough to melt the wire sheathing on the short stretch from the...
  2. Lancer76

    1976 chris craft lancer steering wheel removal advice.

    I'm trying to access the electrical wiring behind the instrument panel, but It's not obvious to me how to take off the steering wheel. Any advice? I don't see any set screws to get a cover off. Thanks in advance.
  3. Lancer76

    1976 Chris Craft Lancer 23 Control Arm Removal

    Hi all, I'm trying to remove the control arm from a 1976 Chris Craft Lancer. It's a single control arm possibly made by Marmac. There was a set screw at the bottom of the arm that I have removed. The arm is on a horizontal splined shaft that goes back behind the the vinyl siding upholstery. I...
  4. Lancer76

    Why is my carb oxidizing????

    This is my second carburetor in 5 years. This one I installed last season. Fresh water boat. At the end of the season, I sprayed it with lubricant, took out the battery, did all the other winter maintenance stuff and covered the boat with shrinkwrap. Now, here we are in spring and I reinstall...
  5. Lancer76

    1976 Mercruiser 233 (Ford 351w) carburetor issue

    I have posted before about the state of my 2 bbl Rochester carb for this motor. In summary, I 'over-cleaned it such that the zinc plating and any other anti corrosive coatings were dissolved and removed. Over the winter (Northeast US) while my boat hibernated, I purchased a 'new' carb. It is...
  6. Lancer76

    MC-1 to Alpha Fitment Question

    My 1976 MC-1 drive (SN 4518534) gave up the ghost today. The drive shaft still turns and there was not burned rubber smell, so the coupler is okay. With engine running I shift forward, and the motor revs, but no prop movement. Same with reverse. With engine off and the shift lever in neutral...
  7. Lancer76

    Carb corrosion.

    1976 351W Mercruiser 233. Cleaned my carburetor completely late last season and my fuel system earlier this season. All was good. Idle at 600 and smooth through the power band. Until it didnt idle. Will run at 1000 RPM smoothly, but when I drop it back to idle it lopes a few times and dies...
  8. Lancer76

    What would cause sudden loss of power?

    1976 mercruiser 233; Ford 351 with Rochester 2bbl carb. Engine starts easily and idles fine. Engine runs great at 35000 rpm for a few minutes and then the engine quickly looses power as if I pulled the throttle back. If I pull the throttle back quickly the engine will continue to run at low...
  9. Lancer76

    Questions About Fuel Tank Cleaning

    1976 Chris Craft Lancer with same model year Mercruiser 233 and MC1 outdrive. I have only been on the water twice in 2019 (short season in Maine). I noticed that the engine starts and runs great until I've been 3/4 throttle for 10-15 minutes or so. At that point, the engine drops out as if...
  10. Lancer76

    Help to ID these parts

    1976 mercruiser 233 with MC-1 Sterndrive. These two parts were in a small box of other parts that I am going to put to use (lower shift cable parts). I'm not even sure these are boat-related. Possible related to a gimbal bearing alignment tool? Any help is appreciated. The upper item is...
  11. Lancer76

    Is a swim platform advisable

    I have a I/O boat - 1976 23' chris craft lancer. It came from the factory without a swim platform, but it has a folding transom ladder so getting on the boat from the water is doable. I have been considering installing a wood swim platform but not sure I want to mess with the original style...
  12. Lancer76

    Stuck Brass Barrel for Lower Shift Cable

    1976 Lancer with a mercruiser 233 (Ford 351w) and MC-1 Alpha. I am changing my lower shift cable and found that I cannot lift the brass adjustment barrel out of the receiver. I removed the cutter pin already. Funny thing is that I have removed the barrel easily several times this season for...
  13. Lancer76

    Mercruiser 233 ford 351 W coil voltage

    I've been having intermittent issues with my 1976 ford 351 W mercruiser 233. Compression is good in all cylinders and swell and timing are right on, but after the engine warms it can run rough, die a at idle, backfire occasionally, etc. All fuel filters changed and runs great on the hose...
  14. Lancer76

    Help with tuning a rough running 1976 Mercruiser 233 (Ford 351W)

    1976 Lancer with Mercruiser 233, S/N 4518524. I purchased this boat last year and tracked down a cooling problem, which I resolved. It was running great until I decided this year the the dwell angle was a bit too large. Well, I adjusted the points and the timing to 10* BTDC, but I had a heck...
  15. Lancer76

    Proper angle for timing light

    I am timing my 351 W and have a question. Engine SN is 4494638 1976 mercruiser 233. I've set the dwell angle and double checking timing. The question I have is 'what is the proper angle for the timing light?' I looked at the timing sticky and didn't see the answer. The stationary timing...
  16. Lancer76

    Warner Tachometer Question

    My Warner Tachometer pegs when the power is applied it remains pegged whether the engine is running or not. However, the power must be on. When power is off, the needle drops to 0. It used to operate correctly and then is was intermittent. Now it doesn't operate correctly at all. The power...
  17. Lancer76

    Hydraulic trim tilt hose fittings

    I have a 1976 Mercruiser 233 with the MC-1 outdrive. The high pressure trim tilt hose from the pump to the outdrive manifold burst. I have some good hoses and manifold from a different boat (the new hose) but i see that the flare fittings on the new hoae are bigger than the original hose ( see...
  18. Lancer76

    1976 Mercruiser 233 RPM and Prop questions

    A new to me Chris Craft Lancer 23 with a MERCRUISER 233. I spent the summer chasing down a cooling issue and replacing a variety of engine and outdrive parts (maintenance things). Fixed the overheat issue and it ran great - just in time to winterize and put away : ( . However, the boat ran up...
  19. Lancer76

    1976 Mercuiser 233 Raw Water Cooling - Help with diagnostic procedures

    This summer, I purchased an almost wonderful 1976 Chris Craft Lancer 23'. The boat is equipped with the original Mercruiser 233 (Ford 351W) with a MR-1 outdrive and was run in fresh water. Prior to my purchase, the boat was covered, but not run for about 2-3 years. When I got the boat, I went...
  20. Lancer76

    1976 Mercruiser 233 Overheating - next steps

    My 1976 Chris Craft Lancer with a Mercruiser 233 (Ford 351 W) and alpha R upper and lower sterndrive is over heating at high RPM while in the water but not while on muffs. Will idle along ok in water and muffs. I've swapped the raw water impeller, new 143* t-stat, new marine water circulation...
Top