Search results

  1. mattkenton

    Looking for steering arm replacement thread or help.

    I have a bad steering arm assembly and i heard rumor that there was a thread on replacing one. Anyone have it bookmarked? I couldn't find it through the search.
  2. mattkenton

    Switching From Idle to Neutral Kills Port Engine 2004 225HP

    Hello, I am having an issue with our port side engine. The engine is a Yamaha LF225TXRC. Sometimes when I switch from idle to neutral the engine cuts off. I have read and searched the net for a couple days and have found multiple sites with this topic. The part in question is called a variation...
  3. mattkenton

    Honda BF20 2HP Issues (White Smoke/Bogging Down)

    Hello all, I have an older BF20 2hp and just started having some issues with it. I have a plan of attack but was hoping that someone may have had some experience with these little engines. When first starting the engine it starts fine and runs fine. Then about 2 minutes into use, it begins...
  4. mattkenton

    Wellcraft 290 Coastal plumbing question and close to tournament day....

    We have been having problems with our livewell and have a tournament coming up. The problem is that the pump will turn on, start pumping, and nothing reaches the baitwell. There is a raw water outlet right next to the baitwell that is getting water. So i know the pump is working. Oh and this...
  5. mattkenton

    Bait Well Pump Issue on 2003, 290 Coastal

    Hello, We have a big tournament coming up and are at our wits end trying to figure out a bait well pump issue. First let me start by saying up until two days ago the bait well did not work at all. I was able to isolate the pump and connect it directly to the battery, it ran. Then removed the...
  6. mattkenton

    Please dont cringe too much....Need help with rotten lugs/rims.

    I'm in the process of rebuilding a trailer that has a TON of surface rust. The rims and lugs are shot, so I need to remove them before sand blasting the trailer. I have a couple questions. If i remove this star nut that holds in the bearing, will this also release the hub from the axle for me...
  7. mattkenton

    VRO to Premix

    Taken From the VRO to Premix Sticky Here: http://forums.iboats.com/showthread.php?t=388154 "Now cut the oil line about 1 ? inchs from motor. Plug the oil line. I use a bolt and hose clamp." After this step i can actually remove the entire oil line to include the oil reservoir can i not? I am...
  8. mattkenton

    Silly Hydraulics! 89 Evinrude Crossflow Trim Tilt Issue.

    Hello, I have an 89 Crossflow 150 that i am having an issue with. On the trim tilt there are three pistons. The secondary two on either side and the primary center piston. My first issue is my center piston. It seems to be leaking fluid out of the top ring/seal of the piston. Is this...
  9. mattkenton

    OMC Wire Cluster Question. Violet/Grey/Black

    Violet is 12v hot wire from Ignition. Grey is tach. Is black an already grounded wire ran from the engine block? Or does it NEED to be grounded. Thanks.
  10. mattkenton

    Fuel Gauge/ Sending Unit Quick Question

    I have replaced all the wires with new ones and have checked all the terminals. The gauge is still not reading very consitant. Double check my wiring i provided please and see if i did everything right. I am going to load test the sending unit tomorrow. But i really think that it is the gauge...
  11. mattkenton

    Help Me Diagnose This Please...Possible Bad Electric Choke

    I have a 1989 Evinrude 150. It has been slowly giving more and more problems on cold starts. It has gotten to the point where it takes a good squirt of Ether to get it going. Once started she runs like a champ. Does this sound like a choke issue? Or is it the fact that i store the engine in...
  12. mattkenton

    1989 Crossflow Thermostat Question.

    Ok so i was running the engine on the muffs yesterday and i touched the port side of the block and it felt a little warm, not bad. Felt the starboard side and it about left a blister. I turned off the engine and opened up the thermostat housing. Thermostat was dry on the backside that opens up...
  13. mattkenton

    Boat Pulls Right...dangerously.

    So i have already adjusted my trim tab on the foot and it helped a little. But it still pulls until i trim up. I am missing a large section of my skeg and it is soon to be fixed. Will this repair help any? WHat other variables cause pull? Sort of stumped. Thanks.
  14. mattkenton

    Did the 89 Evinrudes have designated thermo ports?

    I have an 89 150 upper and want to install a temp gauge. Do they have a threaded plug somewhere intended for this purpose. Or would I be better off with a stud mount type on the block?
  15. mattkenton

    Going nuts. No one knows my model number or serial number. Does not exist!

    Re: Going nuts. No one knows my model number or serial number. Does not exist!
  16. mattkenton

    Going nuts. No one knows my model number or serial number. Does not exist!

    Re: Going nuts. No one knows my model number or serial number. Does not exist! Well that would explain the power reeds. And why it runs like a raped Ape for a 150. Here are the pics anyways. So explain more what a replacement crossflow power head is? Where can i see one not installed? Would...
  17. mattkenton

    Going nuts. No one knows my model number or serial number. Does not exist!

    I have a 1986 150 Evinrude, i think. That was what i was told when i bought the boat. There is no sticker anymore (stupid idea to have something that peels off) and the freeze out plug is not a number that the dealership recognizes. This does not make sence to me. I have a feeling that the...
  18. mattkenton

    Installing a combiner for 2 battery one engine system. Need advise.

    Ok so I am installing a combiner and I have a diagram. I understand everything except the selector switch wiring. In this diagram bot the positive terminals go to combiner and to the switch. What happens when you switch the selector to "all". Does the combiner still keep the house battery from...
  19. mattkenton

    Charging System Issue on a 150 Evinrude..stumped.

    So i have run into a bit of an issue. My batteries do not seem to be charging at all. Here is the back story up to now. Bought a boat with a 1986 Evinrude 150. The main cranking battery (group 31)was taking a 80% charge and the secondary (house) battery would only take 30%. I replaced the...
  20. mattkenton

    1981 Answer 21' Cuddy Cabin with 1986 150 Evinrude

    Re: 1981 Answer 21' Cuddy Cabin with 1986 150 Evinrude So an update of what has happened so far.... -Soft Spot under captains chair (Cut floor, replace wood, refiberglass) Working this out now. These boats were made with a shell, then fiberglassed plywood to shell, then flipped right side...
Top