Search results

  1. B

    Yamaha 115 1996 no power from trim/tilt switch

    Hello all. I have not been out in my boat for a couple of months. When I hit the switch on the throttle, nothing happened. No clicking, nothing up or down. It just does not seem to have any power from the switch. Any thoughts or suggestions?
  2. B

    yamaha 115 hp 1996 stalls

    I have a 1996 115 yamaha. I just purchased. I have replaced filters and cleaned lines. I took it for a test run. I was up on top for about 15 minutes, and going back to the ramp at slow speed, it began to run rough, then stalled. after that it would start and immediately shut down. Any thoughts?
  3. B

    carburetor rebuil

    This question goes against what I would normally do but funds are a little low right now. why do I need to buy a carb rebuild kit, why cant I just take the carb apart and clean it real good and reassemble?
  4. B

    fuel flow issue

    I just purchased a 1996 Yamaha 115. on a 17 mako. fuel was in the internal tank and had been sitting several months. I replaced the fuel/water separator and inline filter. I did not replace the internal filter on the engine. I had problems getting the primer pumped, but was finally able too. I...
  5. B

    1996 70 hp johnson idle problems

    My 1996 70 hp starts and runs great and idles fine when first started. After I have been running all day, and I return to the ramp, the engine will not idle when I put it into neutral making it very difficult to make a smooth docking. I did rebuild the carps about a year ago. I know that I can...
  6. B

    Tacky gel coat

    I made one of those big mistakes and had a "friend " put gelcoat on my deck. It was one coat and it is tacky after 10 days. What can I do to fix it? would a second coat work? I do need to put a second coat on anyways. There is a product called PAV which is a drying agent I think. Anyone know...
  7. B

    adding fluid to power trim/tilt

    This should be a simple fix. I am trying to fill my trim tilt reservoir on my 1996 70 hp evinrude. I have got the engine about half way up. At this point, when I open the reservoir fluid leaks out, and when I add some, most of it leaks out. I don't think I am getting any in and the engine only...
  8. B

    1996 70 HP Johnson float stuck

    I have a 1996 Johnson 70 hp. I recently rebuilt the carbs. Everything worked great until the second time I went out the float in the top card got stuck causing it to overflow. I thought i fixed it, but after several more outings it stuck again. Can anyone explain why it is sticking and how i can...
  9. B

    Trim/tilt goes on automatically

    ?I came in from fishing today and cleaned the boat. A few hours later my son came in saying my engine was making noises. It was the trim/tilt. It just started going down and would not stop. I disconnected the battery and waited. It started again. Any suggestion as to the problem and a fix?
  10. B

    electronic primer

    I recently rebuilt the carbs on my 1996 70 hp Johnson (I was very proud of myself), and the engine was running great. A few hours later I was having problem with a float that needed adjusting. All went well. I then began having trouble staring the engine especially when hot. I researched my...
  11. B

    Too rich gas mixture

    I have a 1996 70 hp johnson. I screwed up and put too much oil in my mixture and fowled my plugs. This engine does to have any rich/lean adjustments. Can anyone tell me how to adjust the gas/oil with out removing the gas in the tank.
  12. B

    engin running very rough and not on all cylinders

    I have a 96 johnson 70. I did not run it for several months. I took it out and it did not run on all cylinders and was very rough. I changed the sparkplugs and replaced the gas/water seprator filter. It was filthy. Any thoughts on the problem? Can I clean the carbs or do they need to be rebuilt...
  13. B

    replacing trim/tilt motor pump.

    Re: replacing trim/tilt motor pump. I hope the diagram shows up. The parts I need to remove are #32 and #34. They hold the trim/tilt unit ontp the engin. I need to remove the whole unit because I need to replace the trim/tilm pump motor. It is a very simple fix, but, of course there is one...
  14. B

    power trim/tilt motor

    I made this post earlier but cannot find it so i am not sure what happended. I am replacing my trim/tilt motor pump and need to remove the pins holding the unit in. I have removed the snap clips but I cannot move the pns. I have I have tried tapping them out but they are tight. my manuel says...
  15. B

    replacing trim/tilt motor pump.

    I am in the process of replacing the pump motor on my 96 johnson 70 hp. I have found that the only way to acces the old pump is to completey remove the whole system.. There is a pin through the rod eye and a rod in the lower end. I have removed all the snap rings and have tried to knock out the...
  16. B

    Need to replace tilt/trim motor on 1996 70 hp johnson

    I need to replace my power trim/tilt motor. It looks like a pretty straight forward job except for one thing. The motor is the square style with screws on each corner. the screws facing out are no problem. The back two screws are the problem. They are located between the transom and the engin...
  17. B

    stuck, tight steering

    My steering on my 1996 70 hp evinrude is very tight, and the steering wheel started slipping and making a loud noise when I turn. The teleflex is new, and I have cleaned and maintained the tube. I think the mounting bracket/tube is full of old grease. Does anyone have any thoughts or experience...
  18. B

    No prime in gas line

    I have a 1993 70 hp Johnson. I attempted to prime the engin with the bulb. I would not prime. I checked for leaks around the bulb and all other connections. I took the cover off, and when I squezed the bulb, it sounded like air was sucking in near the carbs. Any thoughts, ideas or suggestions...
  19. B

    sticky steering problem

    I have cleaned the tube on my 70 hp teleflex. When teleflex is unattached, engin is still very tight. I have been told to heat the area below the power head and remove the grease fitting. I have done this with no luck. I did not heat it for a very long time. Any suggestions???
Top