Search results

  1. joelybob

    NO SPARK

    I had no spark on my 1997 70hp evinrude. I read bob-vt issuu link. it was very helpful. i disconnected black wire from power pack the one on bolt. i tried to start motor and it tried to start so i put black wire back on and it fired right up. two or three times i tried it with no problem. should...
  2. joelybob

    70 evinrude. see anything out of place

    Re: 70 evinrude. see anything out of place
  3. joelybob

    70 evinrude. see anything out of place

    Hi I have a 1997 70 hp evinrude E70TLEUM. I've got running problems fixed on earlier post. now idle is high about 1300 to 1500 rpms. it bounces in between I will post some pictures to see if anything looks out of place. on the carbs the screws a the top they are all different. does that make...
  4. joelybob

    1997 70 hp evinrude not running

    Hi I bought 1997 70hp evinrude (E70TLEUM) last year off a guy. I heard it run. then put it away for the winter. and did not winterize it. guy said he only used non ethyonol gas and I believe him. started it about 2 weeks ago for the first time this year. ran alright. started it again a few...
  5. joelybob

    BRP control box/shifter

    I have a problem with shifter. I haven't had boat in water yet. redid all of inside of boat. so I have been messing with stuff. shifter has worked in the past not on water in the driveway. I messed with screw on front of control box now it wont go into forward gear it will go into reverse. what...
  6. joelybob

    over 1,000 recalls (interesting)

    Recall Database just looking around and saw all these recalls.
  7. joelybob

    steering arm 3 holes

    Hi, I have a 97 70hp evinrude. I was wondering on the steering arm that's is on the motor, that the steering link is hooked to. there are three different holes all in a line , with letters next to them "T" next to 1st hole and "P" on next, and "D" on third .can anyone tell me what they stand...
  8. joelybob

    vro/ different plugs

    Hi, I have a 1997 70hp (E70TLEUM) Evinrude I did away with vro should I use different spark plugs or will there be a difference from vro to pre-mix Thanks ( plugs it calls for are QL78YC )
  9. joelybob

    No spark: 1997 70hp evinrude

    Hi, I have a 1997 70 hp evinrude (E70TLEUM) I bought it last year. it was on a different boat. So I heard it run. started right up. trying to get it going now and it has no spark. I checked plugs and then I checked coil wires they had some build up on them so I cleaned them up. then I...
  10. joelybob

    Classic boat pic gallery (20yr and older)

    Re: Classic boat pic gallery (20yr and older) I have a 1986 SC170 Seanymph my father owned boat over twenty years ago. we sold it and they just wanted the motor and for over twenty years it never went in the water. it was less than a mile from my house all those years. every time I drove by I...
  11. joelybob

    how to wire battery charger

    I want to hook up on board battery charger (attwood model 11900) I have two batteries and I have a perko dual battery switch. I checked forums and the chargers instructions and could not find out how to hook it up with dual batteries. don't know if I hook it up to one battery will it charge both...
  12. joelybob

    Do I need to sand before I put carpet in

    Finally good weather here. just got done glassing plywood. my question is do I need to sand out fiberglass/resin before I put outdoor carpet adhesive down and then carpet or is it not necessary. I am using Roberts outdoor adhesive R6040. Thanks
  13. joelybob

    Fiberglass prep

    Finally good weather here. just got done glassing plywood. my question is do I need to sand out fiberglass/resin before I put outdoor carpet adhesive down and then carpet or is it not necessary. I am using Roberts outdoor adhesive R6040. Thanks:confused:
  14. joelybob

    Time to start trailer rehab

    Re: Time to start trailer rehab Pictures are not the greatest but these are the light plates that came with my trailer just to give you an idea. note that i removed i bolt. have not put it back in since trailer resto. hope this helps. again sorry about photo quality
  15. joelybob

    The Official Post a pix of Your Sea Nymph Forum

    Re: The Official Sea Nymph Forum for seanymph Boat Owners Re: The Official Sea Nymph Forum for seanymph Boat Owners Proud owner of a 1986 SC170 Sea nymph Fishtracker currently being rebuilt. just waiting for warm weather so we can glass plywood floor. Didn't take many pictures of progress as...
  16. joelybob

    1997 70hp oil injection question

    I have a 1997 70hp evinrude with a remote oil injection my question is should I leave it injected or should I premix it. I bought motor in the late fall so I only muff tested it when I bought it. if it is a remote injection is that a vro or is that something different. how reliable is the...
  17. joelybob

    windshield for 1986 SC170 SEA NYMPH FISHTRACKER

    HI, I am looking for a windshield for my 1986 SC170 side console sea nymph fishtracker. dont know if any one can help me. I am rebuilding a boat that my father bought 20 yrs ago.He is gone now so boat is kinda a memorial to him. he loved fishing i have been hard at work cleaning out boat . I...
Top