Search results

  1. KCKracker

    Placement of vapor blower hose? no idea where to mount intake side?

    the boat i am just finishing up redoing is a 19' galaxie I/O with a merc 165 and a 250 inline 6 cyl. The blower hose for gas fumes was missing and im putting a new one in, i know one end goes to the blower but where does it end? where would it be mounted at the intake end for optimum vapor removal?
  2. KCKracker

    Anyone have pics of mercruiser 165 original fuel line routing aroujnd engine?

    my engine just has a hacked in rubber line from carb and a bent up steel line not hooked up, would love to make a new line the route of the OEM one.
  3. KCKracker

    Mercruiser 165 will not go into forward.

    i was test running it a month ago all good. i did some cleaning up of the wires now it will not go into forward. i removed the cable from the control box and it goes forward so i know its not in the control box. what would cause this? i haven't monkeyed with anything in the rear except zip tying...
  4. KCKracker

    what ez steer bracket fits pre-alpha?

    thats it just trying to find out what ez steer bracket bolts to a merc 165. it hink its a 30010 but not posative
  5. KCKracker

    Controls question- trim?

    I just got my first I/O. when taking off and cruising do you run with your trim all the way down?
  6. KCKracker

    Mercruiser 165, why do i have 2 oil pressure sensors?

    i have 2 a little one and a large one. i know one goes to the gauge, where does the other ones wire go to? is it an ignition kill? Its not shown on my wiring diagram.
  7. KCKracker

    Mercruiser 165-- Ballast resistor question

    I am rewiring my boat and removing the old resistor wire. according to diagrams (which none even have the correct color coding as my wires), my resisted wire is between the coil and the engine harness plug. I am going to replace with a ballast resistor, i was planning to mount it under the dash...
  8. KCKracker

    Mercruiser 165 outdrive, can i add a trim gauge?

    I have a 1974 mercruiser 165, motor SN unknown, but the OD SN is #378206, my boat doesn't appear to have come with a trim gauge, I dont like running back n forth, is it possible to add one in the existing sensors or buy some aftermarket stuff? Thanks.
  9. KCKracker

    looking for prop indentity help

    i am trying to find a affordable used prop locally and i cant decipher the numbers mine currently is a 14.25x21 on my merc 165. im looking at one the guy says the only numbers are 48 832332 415 21P. i cant find any info on it
  10. KCKracker

    Dwell on a mercruiser 165?

    i keep getting told to check dwell, and i have a dwell meter, but how do i set it or check it on a motor that wont start yet? i dont know if its far off or set.
  11. KCKracker

    Cannot change email address

    i tried emailing a few times no response, i cannot get my email address to change.
  12. KCKracker

    Mercruiser 165, wont start, have fuel n spark?

    I just got this from a friend, it started and ran last season. i have new points set to .017, new plugs, wires, cap, rotor, coil, and spark. but it wont fire, fart, pop, nothing. not even priming with gas or ether. with ether and spark it should at least fart. maybe my firing order is off...
  13. KCKracker

    How do i get the right bimini top?

    I am looking at lots of good priced local canvas tops or bimini tops, but aside from beam width how do i make sure it fits the contour of my windshield? i have a 74' Galaxy bow rider
  14. KCKracker

    Need advice on a glass boat paint job

    so i bought a little beater that looks like a livingston type boat. ugly as hell. what can i use to put on the inside like paint or? to make it nice. and also economical.
  15. KCKracker

    Evinrucde 89' 88 special, loses power after 2,000rpm

    its my buddies. it runs and idles great, gets up and scoots but at 2,000 rpms it tops out, thats it :confused: it wont go past 2000rpms
  16. KCKracker

    Looking for some info on buffing / polishing / waxing

    I have always used meguires marine rubbing compound and wax. but im a bit confused as to should i be using polish then wax? its never seemed to make a difference :confused:
  17. KCKracker

    Evinrude 1995-175hp cant locate a wiring diagram

    does anyone know where i can find a wiring diagram? working on a friends boat and a shop hacked his wiring, nothing works now
  18. KCKracker

    HELP!! 1977 200 hp v6 alarm

    So I'm at the water right now, I go to turn the key to start my main its a 1977 200hp v6 and the control box is buzzing loud. It's never done this and last start up two days ago all was tip too. I didn't even know it had an alarm. What will set this alarm off being a 1977?
  19. KCKracker

    head bolt torque spec for 1977 johnson 200 V6 ? cannot find

    i need the torque spec and pattern if there is one for 1977 Johnson 200 v6, cant seem to find one and my manual is missing :facepalm:
  20. KCKracker

    Evinrude strange issue, cant pull the cord when plugs are in, plugs out its easy ????

    blue lid evinrude 30 hp ok let me elaborate. buddy brings me his motor and says he was cruising along and then it made a noise, looked back, saw some smoke and he shut it down. then its dead. i immediately see a few slightly melted spots on his wore shielding so i pull the flywheel, i find...
Top