Search results

  1. S

    Missing parts 1991 3hp

    I can't tell what that second picture is....
  2. S

    Missing parts 1991 3hp

    31 must be the fuel line....part 30 is described as a roll pin and not used on some models.
  3. S

    2012 E-tec 25

    https://www.google.com/search?q=how+to+start+a+2012+25hp+e-tec+pull+start&oq=&gs_lcrp=EgZjaHJvbWUqDAgEECMYJxjqAhiMBDIGCAAQRRg6MgwIARAjGCcY6gIYjAQyDAgCECMYJxjqAhiMBDIMCAMQIxgnGOoCGIwEMgwIBBAjGCcY6gIYjAQyDAgFECMYJxjqAhiMBDIMCAYQIxgnGOoCGIwEMgwIBxAuGCcY6gIYjAQyDAgIECMYJxjqAhiMBDIMCAkQIxgnGOoCGIwEMgw...
  4. S

    2012 E-tec 25

    Okay, just got back to this....got the new rope guide piece back on and while better, it's still a beast to pull. Tried to get it to run but no joy yet. To back up, I had downloaded some E-tec stuff and I hit Crosby's stuff but when went to open his file or files it wouldn't open and said some...
  5. S

    1982 Johnson 50 Sea Horse - Constant Beep While Accelerating

    Ahhhh.....pond hockey and lobster rolls.....what could be better!
  6. S

    1982 Johnson 50 Sea Horse - Constant Beep While Accelerating

    All sounds great, go run that thing like you stole it!
  7. S

    1986 johnson 20hp tiller electrix start

    Pretty dirty but the butterfly is perfect. Get the kit and rebuild it. Red lines indicate where you can tap the nut to get it off. The tapping will leave a mark and that will tell you how to put it back the same way. The linkage on the left side will just pull out of the plastic socket if you...
  8. S

    1986 johnson 20hp tiller electrix start

    Butterfly is opening all the way? Completely flat?
  9. S

    1982 Johnson 50 Sea Horse - Constant Beep While Accelerating

    If the lower dropped a 1/4 to 3/8 inches than it's the shaft to powerhead problem. If it didn't drop at all than massive corrosion in the bolts which just requires heat. If the shop is experienced with these motors problem 2 will be easy.
  10. S

    1986 johnson 20hp tiller electrix start

    Merc tank doesn't matter as long as it's a good clean tank. Gray fuel line separated on the inside causing havoc. Linc and sync is how the carb and timer plate work together. With the motor off, slip it in gear, turn it to full throttle and take a picture of inside the carb.
  11. S

    1986 johnson 20hp tiller electrix start

    Good advice really, but I've loaned motors out and I've had my kids use them and they didn't always come back perfect. Simple procedure works quite often really. I find those carbs very easy to work on.
  12. S

    1986 johnson 20hp tiller electrix start

    Another tip... and some do not agree on here, to remove the carb without removing the starter assembly, hit the port carburetor nut softly with a punch or screw driver to remove it. Saves quite a bit of time. Re- install the same way.
  13. S

    1986 johnson 20hp tiller electrix start

    Here is three options. Don't remove carb but remove bowl drain, idle circuit screw and pump the primer ball. If the carb is good often time that will flush it. Remove carb and do a semi-clean, inspect and r&r the parts. Pull carb and do a complete rebuild. When doing option 1, you can poke a...
  14. S

    1986 johnson 20hp tiller electrix start

    Could be the main jet....easy to get to. Main jet is about 1/2 to 3/4 past the carb bowl drain nut. I use torch head cleaner tips. Float bowl could be off or needle. Butterfly opening all the way?
  15. S

    2000 30hp Johnson possible water restriction/over heats

    Ok, eBay had a gearcase for sale.....zooming in I see what it should look like. Clearly isn't the one you have.
  16. S

    2000 30hp Johnson possible water restriction/over heats

    If your addressing me, then no. That system check came with my 3 cylinder 96 25 Johnson. Not sure why they didn't have a system check tach but it's better than nothing. I was just wondering what the OP had for a hot warning device....not sure why this is being so hard but maybe the parts...
  17. S

    2000 30hp Johnson possible water restriction/over heats

    My 3 cylinder 25 came with this system check gauge....did yours?
  18. S

    2000 30hp Johnson possible water restriction/over heats

    Parts breakdown for your motor looks just like the one your using. OEM #0437907 I included a Sierra pic too Not sure what's going on.
  19. S

    2000 30hp Johnson possible water restriction/over heats

    Which pump kit part number did you use?
  20. S

    1993 fast strike 150 carb jets

    When I looked they were in the 50's for the 150 and in the 60's for the 175. It was confusing so I shut my mouth.
Top