Search results

  1. P

    Force 125 cuts out above 4000 rpm

    My 1987 Force 125 hp idles and runs good, starts easy, and accelerates ok out of the hole. But.... it begins to cough and sputter if I leave it at wide open throttle; it will intermittently drop down to 3500 rpm, then surge back up above 4000. If I back off just a little, and run at 4000, it...
  2. P

    Placement of little collar on top of 125 HP lower unit drive shaft

    I had my lower unit off my Force 125 hp, Mod 1251X7B Ser 3795 As I was trying to lift it up for re-installation, I managed to pull off the little collar that slips over the splines at the top of the vertical drive shaft. Now I don't know which way it goes back on: Flat side up, or groove side...
  3. P

    Where do I hoist a Force 125 HP outboard motor from?

    I have ambitiously chosen to replace the motor leg cover and steering bracket on my 1987 125 HP Force. Bought this one...
  4. P

    Is this the right outdrive?

    I am looking for a lower unit for my 1987 125 HP Force outboard. Force 125 Mod 1251X7B Ser 3795 I think this one is what I need: http://cgi.ebay.com/ebaymotors/FORCE-OUTBOARD-LOWER-DRIVE-UNIT-125-HP-/180710749175?pt=Boat_Parts_Accessories_Gear&hash=item2a133333f7#ht_500wt_975 But seller states...
  5. P

    Stiff Steering

    My 1987 Force 125 HP outboard has hydraulic steering, and it seems awfully stiff. I have disconnected it from the motor, and the wheel turns freely when sliding the ram back and forth. The motor, however, is so tight you can't pivot it left and right by hand. Should I be able to? Any...
  6. P

    Grease fitting popped out

    Uh, oh. My 1987 Forcer 125 hp is getting so old the aluminum is soft in places. I tried to lube the king pin ( # 37 here: http://www.boats.net/parts/search/Merc2/Force/125%20H.P.%20%281987%29/1251X7B/MOTOR%20LEG/parts.html) And the grease fitting popped out of the bracket. Actually, two...
  7. P

    Force 125, 1987, Vent and Drain Screw Gaskets/Seals/Washers

    Anybody know a source to buy the gaskets/seals/washers that go around the vent and drain screws at the top of the lower unit of my 1987 Force 125 outboard? The ones for Mercury outboards look like they sorta fit, but I'd prefer to have one specifically made for Force.
  8. P

    What's an L-drive?

    I just bought a Trophy CC with 1987 Force 125 hp. I am checking ebay for service manuals and found this: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=320606737480&ssPageName=STRK:MEWAX:IT#ht_500wt_749 How can I tell if I have the L-drive? Any suggestions for the best place...
  9. P

    Glastron Jetdrive?

    I'm looking at a boat on craigslist with a 455 c.i. and a jet drive. http://providence.craigslist.org/boa/1945032040.html I've had outboards (Johnson and Merc) and I/O's (Mercruiser). I liked the outboards better because of the easy wintertization and low maintenance. Has anyone had any...
  10. P

    Replacing a Mercruiser V-6 with an 888

    I am looking at a 1987 Glassmaster 19' Cuddy Cabin that needs an engine. Current owner says it "had a V-6". http://newlondon.craigslist.org/boa/1438098155.html I currently have a Ford 302 and Mercruiser 888 drive in my 1973 Cruisers Inc. What do I need to know if I am considering installing...
  11. P

    Mercruiser cut out switch lever screw

    I'm having problems with slow shifting and stalling on shifting on my Mercruiser 120 (1973).<br /><br />What I've learned so far is that this if often a symptom of problems with the cut out switch (shift interrupt switch).<br /><br />I cleaned up and lubed the switch, and it seems to be "making"...
View older results
Top