Search results

  1. J

    omc 110 v4

    Question, my engine is charging upto 15 volts, will this damage anything? Just repl;aced the regulator two yrs ago, it is water cooled under flywheel!
  2. J

    110 omc v4 charging

    Question, My motor the charging is going up to 15 volts, i replaced the regulator, 2 years ago, is the regulator bad again? it is water cooled mounted uner flywheel!
  3. J

    charging omc 110

    Question, i used my boat the other day for the first time in like 2 weeks the motor omc 110 when runnning at hi speed was missing. i did flood it while starting, after running it for a while it did clear itself out, i juat changed these plugs so it was the second time out, could plugs have been...
  4. J

    INTERNET SCRIPT ERROR

    Hi i am keep getting this message pop up on my computer it says error: object does not support this property or method, how do i get rid of this!
  5. J

    rpms

    I have a 1986 110 omc now with a 15 pitch ss prop getting about 5800 rpm loaded, as the weather gets hotter the motor will lose some rpms like go down to 5600 rpm is this normal ?
  6. J

    champion L77JC4 plugs

    Question , i changed the plugs in my motor omc 1986 110 hp, i put L77JC4 plugs in the motor, the old plugs were a QL77JC4, they are gapped at about 040 are these L77JC4 plugs ok to use in the motor? Thanks for any replys
  7. J

    champion L77JC4 plugs

    Question , i changed the plugs in my motor omc 1986 110 hp, i put L77JC4 plugs in the motor, the old plugs were a QL77JC4, they are gapped at about 040 are these L77JC4 plugs ok to use in the motor? Thanks for any replys
  8. J

    water pump 110

    Question, i just replaced the water pump on my engine the complete pump, the impeller has an o ring that sits between the grove on the impeller and the plate the impeller rides on, this is how i assembled the pump back together, i hope this was the right way any insight on this. the waterpump...
  9. J

    engine height

    my engine 110 omc is mounted with the cav plate even with bottom on the boat can i go up 1 hole higher, i am getting 5600 rpms now that is with a stainless steel prop, is it safe to go higher? :confused:
  10. J

    110 v4

    Question, anyone know what the compression ratio is on a 1986 omc 110 v4 , just curious, in the 1970's i had a 1966 289 hp ford engine 10.5 to 1 compression ratio, you never here waht they are for the 2 strokes! thanks ;)
  11. J

    seafom in crankcase

    I changed my oil in my 1994 jeep today and added about 8oz on seafoam to the oil, inline 4.0 has 161k on engine always changed the oil at 3k , got the jeep with 110k on it, question do you thing it is ok to leave the seafoam in it for 3k miles till next oil change ? it has the famous lifter...
  12. J

    johnson v4 gearcase

    I wanted to know if anyone knows how many tubes of marine gear oil are needed to fill my gearcase after i drain it for winterizing, should two tubes do it? :confused:
  13. J

    flush with soap

    Question i was running my 110 johnson on fresh water flush muffs, i heard you can used liquid dis soap to help flush the salt. i removed the hose to each head by the thermostat put liguid soap and reconnect hose start up motor run it on flush, is there another way of running soap through the...
  14. J

    wot rpm stainless props

    Hello, i have a 1986 110 omc runs very good, rebuilt 3 yrs ago, it is on a 19ft angler, the props are both ss 15 pich gives me 5600 rpm, the 13 pitch gives me 5800 rpm, that is with just myself on boat, the cav plate is even with the bottom of boat, which prop would be best to use?the boat comes...
  15. J

    carb problem v4 crossflow

    I have a 1986 110 v4 always ran perfect. today i tried to adjust ( and did ) the butterflies so that they were fully open at wot throttle! now the engine runs lousey at idle it spits and some times stalles, question should the butterflies be fully closed when motor is off in netural? why is it...
  16. J

    tilt trim weak

    I took my tilt trim motor off to test the motor to see if if would work, it spins freely put the motor back in and it runs and it will go down but not back up! out fluid in and motor just keep running when push the switch, now i also put a new o ring on the manual screw and i can not get it back...
  17. J

    tilt trim relays clicking

    Hello, new problem my 110 omc tilt trimm just clicks now, had relys switched still just clicks, everyting just stopped today! ant ideas on what is the problem? motor is a 1986 johnson on a 19 ft angler boat! had the box out checkin the wires can not get it to work!
  18. J

    manuel release trim screw leaking

    i have a leaking trim screw for the manuel release, questions should the screw back out all the way to remove? is their supposed to be an o ring to stop leak? how do i get this screw out to investigate? motor is 110 omc thanks for any replys
  19. J

    please help

    sorry for being a pain, but i have this manual release valve leaking on my 110 omc trim tilt unit. the screw turn in and out not stripped it leaking trim fluid from recessed screw, how do i fix this i am out of work now and will have to do the repair myself, i have the boat out on trailer in my...
  20. J

    trim tilt leak

    Today i had my son and nephew on the boat and the trim tilt stopped working, it leaks from the manual release screw, can i leave the screw loose and use the tilt manually till i acn get the motor fixed? or do i have to turm the screw every time i want to tilt motor? motor is 110 with a 1 year...
Top