Search results

  1. J

    wot rpms v4 110 hp

    I have a 19ft cc boat, motor is 110 mounted with cavitation plate level with bottom of boat, with a 15 sst prop getting about 5600 rpm with just myself on boat, with a 17 sst prop getting about 5200 rpm with myself on boat, i weight about 210 lbs, question is it safe to use the 17 sst prop? boat...
  2. J

    trim tilt

    Hello i have a 1986 110 johnson, the motor when trimmed all the up is very slow going down, hold button for about a minute before it starts to go down, trim motor is new and running the whole time, could it be airbound in the pistons? thanks for any input
  3. J

    power trim 110 johnny rude

    Hello, i am having a problem with the power trim on my 110 johnson, the trim motor is about 2 yrs old, problem: when motor is trimm all the way up, it takes a very long time before it will go back down! the trim motor is working the whole time, it also makes weird noise going up or down, could...
  4. J

    erratic tach 110 omc

    I have this tach that works sometimes and cuts out, i have checked the battery and have over 13 volts, the volt meter on the dash reads over 12 volts, the battery is charging and is a " good battery, it is 3yrs old but still starts the motor, could this be a bad ground somewhere, i have cleaned...
  5. J

    Max wot rpm

    What would the max wot rpm of a 110 v4 evinrude crossflow be ? i have it on a 19 ft center console, using a 13x15 aluminum prop getting abot 5600 rpms now. with 2 adults on board, is this rpm too low or is it acceptable. the motor is mounted on an old manual jack plate, i have the anticaviation...
  6. J

    aluminum plate paint

    I have a aluminum plate bolted to the transom, iwanted to paint it with rustoleum paint, and then top coat with bottom paint to keep the growth off, just wanted to know if anybody tried this procedure before? The boat is 19 ft cc with 110 omc off the back!
  7. J

    bilge pump

    I have a 19 cc anglar boat i keep it docked at a marina, it has a 500 gph bilge with a float switch was wandering if it is big enough for the boat? should i install a 1100 gph pump. the pump that is in there now is about 3 years oild it is a rule, it is not a fully automatic one, it has a float...
  8. J

    dock space

    I have a 19ft anglar center console just paid $1300.00 for dock space for the season, seems kinda high too me, just wandering what going rate would be?
  9. J

    recommented rpm

    I just wanted to know what the proper rpm for my 110 omc v4 should be it is on a 19ft angler center console, i have many props laying around should it be 5800 or 5500 rpm @ wot, the guy in the parts room at a local shop said 5500 for that motor but looking at the board i think Dhadley said...
  10. J

    delamination

    I have a 19 ft angler has a acess plate round mounted onto floor the plate has been missing for some time the edges around the hole have seperated. question: can i just fill in the edges with some polyester resin before i put the new acess plate on?
  11. J

    rpm range

    I put a 19in stainless prop on my 110 evinrude, it is on a 19ft center console, with myself and my son motor did 5200 rpm top speed trimmed out, the boat was moving fast, thinking that this is not enought rpm for this engine, what size sst prop could i put on to get 5800 rpms! thanks for replys :)
  12. J

    thermostat white poppet valve

    Question , i am changing my thermostat in my 110 johnson, on the white poppet valve how big of a hole should i drill in to each valve, i already drilled a two 1/16 holes in each, but it seems very small! could some help me out with this! Thanks
  13. J

    job

    Well lost my job yesterday, doing inside sales for electronic parts, prior to this worked for northrop/grumman for 15 yrs! any one looking for any help on southsore long island?
  14. J

    bosh platinum spark plugs

    I replaced the spark plugs in my jeep today with bosh platinum plugs, the 4.0 has 147K on the engine, are these plugs better than the standard autolite plus that i had in there? the auto lites had 16K on them and seem to be missing when takeing off from a cold start. the jeep would hesitate from...
  15. J

    transmission jeep

    Question: i have this 1994 jeep grand cherokee with a automatic transmission rebuilt with about 20k on it, i put that lucas transmission stuff in it as was wandering if it would do any harm to the unit, it is shifting kind of strange it seems to down shift at a higher speed now. was thinking of...
  16. J

    94 jeep no start alarm

    I used my jeep 1994 grand cherokee, 4.0, was running fine, went in saw a movie came out ad went to start the jeep and the lights start going on and off with the horn beeping on and off with a security light up on dashboard! this never happen before no alarm on the car ever! tried to start it and...
  17. J

    1994 jeep 4.0

    question: how is a distributer cap good for? i changed mine to today after about 36k miles on it! the engine was running funking in the morning, plugs air,gas filter all changed figured i change out the cap and rotor no crackes in it but miles getting high on it! just hate to change parts and...
  18. J

    rocky racoon

    today me and son went out to take the boat out of the water, while i was driving the boat i felt something brush up on my leg i look down and there was this racoon walking around apprently his was below the hull and came up thru and open port hole. scared the hell out of me,i let him walk around...
  19. J

    water discharge

    i was wandering at high speed my motor 1986 110, the water discharge is coming out of the thermostat is hot to the touch this is at high speed only, the temp is not reading hot nor does the overheat alarm go off. at low speed no discharge out the thermostat only the pisser hose which is not hot...
  20. J

    shocks 1994 jeep grand cherokee

    i have a 1994 jeep with 141000 miles on it, it has the original shocks, was wandering was kind of shocks to replace with besides monroe, any suggestions, thanks for input! :cool:
Top