Search results

  1. G

    Any Idea's on flush valve ?

    I have a 1997 5.7L 350ci Mercruiser Bravo II XL with closed cooling. I want to install a flush valve other than down in the bilge. There is no shut off valve. Only have to flush heat exchanger and risers ? Thanks for any help.
  2. G

    water pump impeller

    Just to make sure, what way do I turn the impeller to seat it in the housing on a 6 hp. evenrude ? Thanks
  3. G

    Opinions on exhaust manifolds

    Going to change out the exhaust manifolds and risers on my 1997 closed cooling 5.7L Mercruiser 350 LX, am I better off going with the newer dry joint set up or stay with the old style ? Thanks
  4. G

    1986 6hp. Evenrude E6SLCDE

    Guy's does this motor have a tell tale ( pisser ) to tell if the water pump is working ? Thanks
  5. G

    Apprarisal for Boat

    Hello; Hope this question is in the right place. I can not find the selling price for a 1996 22foot Aquasport C/C with a225 Evenrude Ocean Pro. Can anyone tell me where to look ? Thanks
  6. G

    Oil level

    Maid a mistake while changing the oil in my 350 c.I. Mercruiser. I now have oil level about one half inch above the full mark on the dip stick. Does this have to come out before starting the motor ?If I can run it to warm the oil up I will bring the level down. Thanks
  7. G

    S/S Prop

    Any one have any tricks to keep a S/S prop from getting the crap on it when slipped in the salt for six or seven months ? Thanks
  8. G

    Cone Clutch Shift Bravo II

    Hello; I have a 1997 5.7L LX with a Bravo II drive. The drive is very hard to shift. I have replaced the shift cable and the helm shifter also lubed everything.Also pulled the cover and cleaned the shift d-tent and applied new grease , and the drive still shifts hard. I have to push and pull the...
  9. G

    1990 Force 150 hp.

    Changing water pump impeller, how do I disconnect the shift shaft ? Thanks for any help.
  10. G

    Force 150 hp. water pump

    Doing my first water pump on a 1990 Force 150hp. just want to know if there is anything to be aware of ? Any tricks ? Thanks for any help.
  11. G

    1986 Evenrude Yachtwin

    Can someone steer me to a diagram of the cooling system for a 1986 6 hp. Evenrude Yachtwin ser.# 329909 Mod #E6SLCDE ? Thanks.
  12. G

    Bravo one verses Bravo two drives

    Are these two drives interchangeable? Any advantages of one over the other ? Thanks
  13. G

    8hp. Yamaha

    I am trying to find out what year my Yamaha is, the numbers are 8FS== 6G1== S==038228. Can anyone tell what year it is ? Thanks !
  14. G

    Trim sender

    Hello all; Here's my question; The trim sender on my 1997 Mercruiser Bravo II drive is not working, the gauge is pegged all the way up and does not move when I move the drive up and down .Everything worked fine before winter lay up. Is there a way to test the sender and or gauge to see what...
  15. G

    Timming chain cover seal

    I have a 1997 5.7 L 350 cu. Bravo II LX . The crankshaft seal on the timing chain cover is leaking a slight bit . Does this cover need to be removed to change this seal ? I was hoping this seal goes in from the outside of the cover. Am I lucky ? Thanks
  16. G

    what Evenrude ?

    I just acquired an older Evenrude Yachtwin 6hp. Ser #329909 . Can someone tell me what year this is ? I would like to order a manual for it. I tried iBoats but, the don't recognize the Ser .number. Yhanks.
  17. G

    What distance

    What is the distance from Cape May New Jersey to Bear Inlet North Carolina by boat ? Thanks
  18. G

    Bravo II Drive

    Anyone come up wiyh a home made hoist / tripod for installing and removing a Bravo II drive. If so care to share ? Thanks
  19. G

    U tube vids on Force motors

    Anyone know if there are any u tube vids on changing the water pump impeller on the five cly. Force out board ? Thanks.
  20. G

    2.5 L Mercruiser over heating

    I am working on a 1989 2.5L raw water cooled MerCruiser. 1. New thermostat 2. checked circulating pump 3. new impeller in drive, and verified it is pumping 4. cleaned exhaust manifold and checked with 65 psi. water pressure. 5.cleaned riser 6.installed new exhaust flapper This engine still over...
Top