Search results

  1. G

    Water in the drive bellows

    I have two questions,what do I look for if I have water in the drive bellows and can water in the bellows get into the drive ? Thanks !
  2. G

    Any screen

    Found Problem Thanks
  3. G

    Trim Rings

    I have a 1997 ProLine 231WAC. On this boat is onboard rod storage racks on both sides , can anyone tell me where to get replacment plastic trim rings for these racks ? I've been all over and no luck. Thanks for any help !
  4. G

    Raytheon Pathfinder

    Can anyone tell me the difference between a Raytheon SL and a Raytheon RL. Are the power heads interchangeable ? Can they both be used with the same radar dome ? Thanks.
  5. G

    LED spreader light

    While I was hooking up my new LED spreader lights I reversed the polarity on one for a split second, now it does't work. What did I screw up ? Is it worth fixing ? Thanks !
  6. G

    ProLine 231 WAC

    I have a 1997 ProLine 231 WAC. There is a pocket on each side under the batteries that is about 6 inches square and about 4 inches deep that hold water from wash downs and such. They have no drain holes in them, if I drill a drain hole am I asking for trouble or am I O.K. Don't think there is...
  7. G

    1996 8 Hp. Evenrude

    Is there no way to flush this motor other than in a barrel? Thanks.
  8. G

    Alpha drive upper drive yolk oil seal

    Please forgive me ,I pulled the oil seal out without making note of how it was in.Does the open face go in towards the bearing. Looking at the book and online drawings I can't tell. MY BAD ! Thanks for any help.
  9. G

    Exhaust Gasket

    Hello Guy's; I just have one question, I've looked everywhere but can't find the torque specs for a Mercruiser 2.5L exhaust manifold to cyl head and riser to manifold . Thanks for any help.
  10. G

    Bravo II coupler

    Hello; When lubing the Bravo II coupler from inside the boat , do I need to hit both zerk fittings or is one enough ? The one I could get to I gave nine pumps of spling grease. Am I O.K. ? Thanks.
  11. G

    Bravo II drive

    Hello; Just a quick question. Bravo II drive ser.# OK097356.Took the plate off at the shift detent lever. Is the lower chamber filled with drive oil or just the top one ? Thanks !
  12. G

    Thru hull raw water

    Just a quick question; I have a 5.7L 350c.i. Bravo Xl with a Bravo II drive, is there any benefit to installing a thru hull pick-up for the raw water pump ? Also , it is a closed cooling system. Is it worth the work ? Thanks !
  13. G

    What prop is this

    I came across this prop # 48-83283001-19 or # 48-83286001-19 can anyone tell me what this is for ? Thanks
  14. G

    8 hp Yamaha

    Hello I'm back; I finaly found my problem. I am getting a slight amount of water in the lower cylinder. I found a small hole ( size of a pencil ) in the exhaust manifold, between exhaust and water jacket. Don't know if you could get in there to weld it but, I was thinking about J.B.Weld. Do you...
  15. G

    Anodes

    Hello every one; I was just thinking about ordering a new set of anodes for my Bravo II drive. I run/ slip in saltwater so I use aluminum anodes ( per MC) on the drive. Should I use aluminum anodes on the S/S trim tabs ?? Thanks.
  16. G

    Evinrude 8 Hp.

    Hello ; I just picked up a 1996 8 Hp. Evinrude outboard. It started good and seams to run fine. The question is where to get an owners manual for it ? I need to know gas/oil ratio, what gear oil for this motor etc. Thanks for any help !
  17. G

    SS Prop

    Hello Everyone; Just wondering, anyone have any Ideas how to keep a SS prop clean on a Mercruiser Bravo II drive ? The boat is sliped in salt water for seven months. I have tried wax= no good.How about paint ? Thanks
  18. G

    Windsheild

    Hello; Just giving it a shot, anyone know where to get the strip of rubber at the bottom of the windsheild on a 1997 231 WAC ProLine. It's the one the wires are behind at the base of the windshild. Thanks
  19. G

    8 hp. Yamaha

    I have a 8 hp. two cycle Yamaha , the # on it are 8SF , 661-S- 038228. It is getting a slight amount of water in the lower cyl. Where should I start looking for the problem ? Thanks !
  20. G

    Gimbal bearing seal

    Hello : I have a 1997 ProLine 231 WAC . Eng # OK147937 Bravo II Drive # OK097356 Transom # OK142550. I will be replacing the gimbal bearing soon.The new bearing came with a oil seal, from the stern of the boat does this seal go in first before the bearing or after the bearing ? I have looked...
Top