Search results

  1. D

    navionics/lake master

    have been looking at cards for my hb ff and saw a couple that had rivers on them but none specified if they had the missouri river.does anyone know of a card that has the missouri river on it and if so have you used it on the river,and how accurate did you find it to be?
  2. D

    minn kota all terrain 12v 55lb

    i have above trolling motor on my 1996 landau pro 17,aluminum bass/crappie boat.a friend of mine has a lowe that is damn near identicle but has same trolling motor except its a 45lb.when i first put my 55lb on my boat it would darn near throw me out of the boat on #5 which is max and now my...
  3. D

    spark plug gap

    good morning IBOAT world.....i just just surfing through the new post and came across a thread about spark plug gap,a member had stated that he was going to be doing alot of trolling and didt want to foul plugs while doing so.someone chimed in and said to gap at .040 instead of .030. my ? is,is...
  4. D

    evinrude outboard

    hopefully this little bit of info will help someone out there that is having the same problem i was.... i rescently replace my powerhead on my 1995 88 spl and when doing so i noticed that the small vacuum lines where cracked on the ends.so i cut off the bad ends and put them back on good as...
  5. D

    1987/1995 88 spl erude

    i have a erude 88 spl,the powerhead is an 1987 but rest of motor is a 1995.i have it on a 1996 landau pro 17 aluminum bass boat.i am currently running a michigan wheel apollo 13.25X17p,stainless steel and getting 5000-5200 RPM at WOT and 36-37MPH up river and 42-44 MPH while going down river...
  6. D

    prop change 88 spl erude

    i have a 1996 landau pro 17 with a 1987/1995 88 spl.i have been running a stainless michigan wheel appolo 13.25x19p prop and at WOT i was getting 4600-4800 rpm's,i put a new 13.25x17p on recently and at WOT i now get 5000-5200 rpm's. i want to make sure im running the proper rpm's,what is the...
  7. D

    1985 evinrude 115 tnt

    my power tnt is not working properly,it works just as supposed to in the up possition but when i go to tilt motor down the TNT motor runs but the motor free falls untill it reaches the trim part then it trims as its supposed to.TNT motor is new as of last summer.i have tried everything i know to...
  8. D

    1995 rude 88 spl

    ok evinrude guys i have a problem with my power tilt/trim.first i will start off with all though my tag on motor states its a 1995 i think the tilt/trim is off a diff year and maybe a diff hp. If you look at the parts diagram for [hydrolic assembly] for my motor [model# E88TSLEOC] ther are some...
  9. D

    1996 landau pro 17 w/1987 88 spl e-rude

    i am currently running a 3 blade stainless michigan wheel apallo prop,13.25 inch diam 19 pitch.if i am by myself i get right about 4800-4900 rpm and with me and 1 or 2 other i get right about 4500-4700.either way i get between 44-48mph gps. my ? is im thinking about going to a 17 pitch prop,can...
  10. D

    1987 erude 88spl,spark plug ?

    ok,i have been running the champion QL77JC4's in my motor.i looked @ the plug chart and it says to use either the QL77JC4 or QL82C,can someone tell me what the difference in these plugs are?
  11. D

    mercury 20 hp

    i am needing to try and track down some parts for my cousins outboard motor but we dont know what year it is. only #'s i could find was serial #2337922.can someone please help me find out what year this motor is? it is a 20 hp.
  12. D

    1987/1995 evinrude 88 spl

    i installed a new powerhead on my boat and when i started it,it barely peed out the tell tail and i could see water leaking somewhere from around the lower cover.its not leaking anywhere from where powerhead mounts to motor.any idea what i might check. it prolly doesnt matter but phead is 1987...
  13. D

    1987 evinrude 88spl

    ? about reed valves.my motor blew up at the end of last summer and when 1 of the rods broke it busted the corner off the reed valve for that cylinder.should i just replace that 1 reed or should i replace all of them?
  14. D

    teleflex ch1700 side mount for 1995 evinrude 88 spl

    wondering if anyone has any experiance with this control box?
  15. D

    1989 200hp johnsonGT

    wondering if someone could tell me what the ideal commpression should be for this motor?starbard side from top to bottom i have-80,72,78&port side is all an even 78 all the way down.this is after warming the engine up.before we ran it the #'s where a little higher.
  16. D

    1987 erude 88 spl

    was hopeing some1 cold tell me what the ring tollarance should be on my motor.i had it bored out to 3.544.if i am understanding what i had read,it should be about .025?is this right?
  17. D

    lower unit leaking

    I have a 1995 erude 88spl,i have had it at the shop twice now for this leak.first time they pressure tested it and replaced the propshaft seal.i checked the LU grease just for peace of mind after about a month only to find it was still getting water in the LU. took it back and they checked it...
  18. D

    info on powerhead exchange inc

    Not sure if this is right place to post this question? this seems to be the only place i can find a rebuild kit for my engine.It is called powerhead exchange,it is in tampa florida.Has anyone delt with this buisness,and did everything go smooth with the transaction? Thanks,shane
  19. D

    rebuild kits

    I found some complete rebuild kits on a website for my 88 spl,it is a 1987.they offer 2 kits,1 with caged rod berings and 1 with regular rod berings.Can i use either 1?what is the difference in the caged bering and non caged?
  20. D

    add on Fuel filter

    A friend of mine was looking at my boat and noticed i had a fuel filter that has the cardboard filter inside and told me his mechanic told him not to use the cardboard ones. Is this info right?if not cardboard then what,plastic?And what is the reason for not using? Don't know if it matters where...
Top