Search results

  1. Franco_boater

    Yoke seal

    Thank You, how tight the bearings should be while spinning it in hand When removed from my Yoke it was quite tight...Take care
  2. Franco_boater

    Yoke seal

    Oh didn't know that... so 5.25lbinch is the limit and can be below that value or the final target torque value?
  3. Franco_boater

    Shift shaft bushing removal and install

    @achris I have a question to be 100% sure, I have installed my shift shaft bushing and seal facing UP (spring facing UP) towards U joint bellows, is that correct? so the exhaust side will be like this: And do You think I can use some socket to push/hammer the upper drive shaft seal? its 1...
  4. Franco_boater

    Yoke seal

    I am sorry... He posted this But I cant find this info in 14 manual... and my manual says only 5.25lb-in but above we have some range... why
  5. Franco_boater

    Yoke seal

    Can I reuse the nut from the gear set?
  6. Franco_boater

    Yoke seal

    Ok, before disassembly I will check rolling torque on existing set, then I will try to set a new one after smacking with plastic hammer. I found in some manual there is a range in torque but in my manual #14 it says only the limiting value which is 5.5 lb-in. (0.55 Nm) for used bearings], Also...
  7. Franco_boater

    Yoke seal

    Thank You all is now more clear for me, We have perfect seal, is that ok or should I buy blue silicone??
  8. Franco_boater

    Shift shaft bushing removal and install

    Southern part, Calabria! Do You have any tips when installing this seal ?
  9. Franco_boater

    Yoke seal

    Yes I have checked your video, its very good and resonable for me. 1. Question about light hit, how much hit is enough? How I can recognize the hit relased the pressure? I can try to find or rent this tool maybe? But hitting with copper hammer is easier but I am afraid how much hit is enough to...
  10. Franco_boater

    Shift shaft bushing removal and install

    Thank You, Come to Italy You have to try our pasta! Also Help with yoke seal will be appreciated in other thread
  11. Franco_boater

    Yoke seal

    Good morning, All what I need is to replace only the SEAL and Oring there... but found the info I need to split the bearing thats why I am so concerned.. Boat is in my marina so far I don't know what kind of gear set Ive got, do You have a picture how to recognise them ? Is the picutre above...
  12. Franco_boater

    Shift shaft bushing removal and install

    Thank You or maybe You have better idea for press that seal for DIY? Im studying manual 14 and Ive found step about removing the driven gear bearing cup and shim is that needed for oil seal replacement??
  13. Franco_boater

    Yoke seal

    Hello @achris i cannot edit my post, Ive found picture on the Internet, If I have assembly like this Gen2, where I have to put the bearing separator and how much separate ?? Can You mark it please for me... Thank You
  14. Franco_boater

    Shift shaft bushing removal and install

    Grazie mille! Please tell me, to replace the yoke oil seal and oring, do I have to really separate the bearings before setting rolling torque? I have torque dial wrench thats no problem but I am afraid of separating bearings.... I read method of punching with brass hammer what Don_S said but im...
  15. Franco_boater

    Yoke seal

    Ciao friends, I will need to change upper oil seal there is a leak there, I found information that yoke needs to be replaced, thats OK i have ordered spanner BUT... if all the upper gearcase will be removed its smart to change yoke seal and oring. I have dial torque wrench for that and thats ok...
  16. Franco_boater

    Shift shaft bushing removal and install

    Ciao again, During the weekend we replaced seals, springs, lips facing up , is that correct? Like this, after pressure testing we found leak in upper driveshaft seal, I have 1 seal only but on the internet there is info that there were 2 seals also right? I think i have never version. Do I...
  17. Franco_boater

    Shift shaft bushing removal and install

    Do You mean to install seals before bushing? I was thinking to install upper bushing first, flush it with the top then from the bottom push the seals as much to be seatead against bushing. Correct me if i am wrong. ciao
  18. Franco_boater

    Shift shaft bushing removal and install

    I am glad Ive got the right one, I have a little play in the shaft so I think the bushing is worn or maybe seals only but it's good to replace it anyway. Can anyone tell me how to install the bushings? Push it in from below and install same way or from top to the bottom? Does it even matter...
  19. Franco_boater

    Shift shaft bushing removal and install

    Mine drive is from 2004 Ive removed 2 brass and 2 orings as in 1 picture
  20. Franco_boater

    Shift shaft bushing removal and install

    Ciao from Italy my friends , we have found water leak in my bellows, mechanic changed my bellows, gimball and now I need to change shift shaft seal bushing. My question is: to remove and install the bushing back to the housing, do I have to press it in in which direction? From below to the...
View older results
Top