Search results

  1. Franco_boater

    How to turn V6 engine by hand

    To check alignment, to spray fog tinto the spark plugs then turn the engine or turn the engine after the winter ,
  2. Franco_boater

    How to turn V6 engine by hand

    And with plugs on? hows the best way?
  3. Franco_boater

    How to turn V6 engine by hand

    Engine is on the boat with drive removed
  4. Franco_boater

    How to turn V6 engine by hand

    Hello I have 4.3 V6, can anyone tell me how to turn the engine by hand? I read using 27mm socket is dangerous, but why? In any car its ok to turn the crank by hand. Looking forward for advice Best regards
  5. Franco_boater

    Exhaust bellows

    So whats the trick to install all the bellows? Installation tools?? Im reading all the informations and there is a big PAIN in the ... to change it.. Probably I will need to do this next year and I am gathering all the informations but... Its so difficult?
  6. Franco_boater

    Elbow and exhaust manifold inspection what do you think?

    Ive got it Thanks Chris m But question regarding torque exhaust Manifold to heads. Page 7B-2 says 34Nm but Page 7B-9 says 43Nm …(??) manual #37 Thanks
  7. Franco_boater

    Elbow and exhaust manifold inspection what do you think?

    Im simple man 😬
  8. Franco_boater

    Gimbal ring screws retorque

    Hello, I want to ask You question about retorque gimball screws, Should I loosen the screw and nut and after that reqtorque again? Ive tried 50ftlbs then 55ftlbs and the wrench clicked but still ive got some play on the ring. So maybe the torque value is cheated because of all the crud on the...
  9. Franco_boater

    Elbow and exhaust manifold inspection what do you think?

    So the correct procedure is to retorque elbows/exhausts after reinstalling ??
  10. Franco_boater

    A1G2 decisions. Rebuild or replace?

    No it’s 1st time I’ve said that here
  11. Franco_boater

    A1G2 decisions. Rebuild or replace?

    when I was hammering bearing I inserted the tool with disc but not bolted to the bar, then pulled out a little the bar from the coupler, inserted bigger pipe over the tool and hammered the pipe which pushed the disk with bearing . Works perfectly
  12. Franco_boater

    A1G2 decisions. Rebuild or replace?

    I think you need to slide back 1/4” off towards small end Then make a hole you make this toavoid damaging the splines When hammering the gimbal, so the bearing stops at the race and the tool doesn’t touch the splines….
  13. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    Chris, I dont have loctite 222, only blue one or the red :) or perfect seal Do You think its safe to use blue or perfect seal or better to buy 222 /purple threadlock?
  14. Franco_boater

    A1G2 decisions. Rebuild or replace?

    Im wondering how ?? I tought its safe tool, maybe he didnt displaced the disk so it dont touch the splines when hammering....
  15. Franco_boater

    A1G2 decisions. Rebuild or replace?

    Scott06 you say this install tooll disc mounted on the tool is a wrong one??
  16. Franco_boater

    Gasket under Anode A1Gen2

    Hello boaters, I have a question, Ive got 2005 Alpha One Gen 2 and every year I remove anodes and clean them, now Ive noticed gasket under the anode but i dont have it. Do I need it? Whats for??
  17. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    Ok good night here its early evening, Ive found #37 is for V8 only but Ive got V6 with Dry joints, wondering why
  18. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    I will Thank you for your help. I have manual only for V6 engines @achris can You please post a pages from this manual
  19. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    When You go to parts catalog, here is the picture: and there, you see the gasket with restrictor hole towards the back of the boat, but on this picture: it says: Restrictor hole always opposite of the exhaust riser
  20. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    Thanks AChris for screenshot but i understand this seawater inlet should I put it as on the diagram ? But here it says this
Top