Search results

  1. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    haven't used my fish finder since all this. My stereo is the only other device but its turned off. I hooked a volt meter up to the battery and got the same reading as dash gauge. I know is possible the regulator i bough could be defective.... are there any other aftermarket regulators i could...
  2. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    I installed the regulator and double checked my wiring and I am still getting a voltage spike to almost 16 V!!! Could the stator be bad? I’m running out of ideas here
  3. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    Thanks for your help i will install this part and hopefully the voltage will drop.
  4. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    Can somebody please help me find a wire diagram for this voltage regulator?
  5. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    If I remove this bracket can I install the regulator (part # 585195)??? Some of the regulators I’ve seen are water cooled and come with a gasket and others don’t have a gasket. Trying to find one that will work.
  6. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    I thought the same thing but the serial numbers match on the block and the midsection. According to the parts diagram for this model it should have a voltage regulator. Can you tell from the picture that it is missing? or is there not a place to mount one? Is there another way to regulate the...
  7. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    Here are a few pics of the motor. It looks to me like there is not a voltage regulator installed….
  8. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    The batteries are brand new and almost all the wiring has been redone and cleaned up. Do you have a link for this? Part #? How are these installed in the circuit? Thanks!
  9. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    Here is a pic of the rectifier on my motor
  10. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    Thanks. I purchased a new rectifier and ill give that a try. https://www.ebay.com/itm/203281683858
  11. B

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    Hello, I have a question about my model J90TSLECM johnson motor. I took the boat out for the first time and noticed that the voltage when from 12V at idle to near 16V at faster speeds. Any ideas on how to fix thing?!?! Thanks
  12. B

    Johnson 90hp alarm buzzer

    part # or link to a Johnson alarm buzzer???
  13. B

    Johnson 90hp alarm buzzer

    120 across the board. i checked the fuel filter and it was clean but i notcied a lot of white sediment and particles at the bottom of fuel water separator. i cleaned everything out but thought i should mention.
  14. B

    Johnson 90hp alarm buzzer

    control box does not have a warning horn. i need to install one. Can someone help me find the correct part? I took the boat out for the first time once it i got it to full throttle the motor would studder and end up stalling then hard to start up again. it runs great other than at full throttle...
  15. B

    Johnson 90hp alarm buzzer

    Ok that makes sense. These are not hooked up to anything. They should be wired directly to the ignition ( which is separate) right? I’m assuming the alarm buzzer and neutral safety switch is built in to the control box and might work if the yellow wires are hooked up correctly?
  16. B

    Johnson 90hp alarm buzzer

    The boat is at the mechanic at the moment so I can’t send you a picture. The control box seems older and has a three wire orange plug for the trim and tilt and then it has two yellow wires coming out. What are the yellow wires for? Nothing is wired to the ignition from the control box.
  17. B

    Johnson 90hp alarm buzzer

    Hello, I am trying to install the alarm buzzer for my johnson motor (J90TSLECM). When i bought this boat there is no alarm boot sequence when i turn the key so i noticed it was never installed. Can somebody please help me find the correct part number and how to wire it up to the ignition. Thanks!
  18. B

    98 Johnson 90hp tilt and trim not working

    I’ve read that if I jumper the wires on the connector coming from the relay to controller that it should tilt up and down. I’ve tried this and doesn’t work
  19. B

    98 Johnson 90hp tilt and trim not working

    Hello I have a model J90TSLECM and the tilt and trim motor works great from the switch on the motor but will not work from throttle switch OR when I try to jumper the 3 wire plug and harness coming from the relays. Could this be a problem with the relays even though it’s works on the motor switch?
  20. B

    98 Johnson 2 stroke ignition

    Hello, i am trying to wire up an igniton for my 2 stoke and i cant find a diagram anywhere for it. It is a model J90TSLECM. Thanks.
Top