Search results

  1. E

    Starter

    Anybody know the part number on a 1991 evinrude 225 starter. Model e225pxeic.
  2. E

    Seastar

    I am currently rebuilding my boat and had it completely stripped. As I begin to put it back together I pulled out my seastar hydraulic steering pump that had all fluid drained from it prior to removal. It is not turning all the way as it did when full. It has been stored upside down all this...
  3. E

    Evinrude 225 starting

    My 225 91 Evinrude has trouble starting. I am considering rebuilding the starter anyone knows where to get a rebuild kit?
  4. E

    Liquid Nails

    Anybody used this stuff for boat building. Is it an epoxy based adhesive? Will polyester resin stick to it? Any insight will really help.
  5. E

    hard starting

    My evinrude 225 1991 is hard to start. I can hit the choke on it all day and it will start after a few minutes of cranking. But the moment I squirt a little drop of starting fluid in it, it cranks as if it was brand new. I push in the choke when it is running and it does bog down as it is...
  6. E

    Battery isolator

    Was just looking at the new Evinrude catalogs and they said that the new models have a Built in battery isolator. Anyone know if this came on the 1991 225 evinrude?
  7. E

    Battery isolator

    Was just looking at the new Evinrude catalogs and they said that the new models have a Built in battery isolator. Anyone know if this came on the 1991 225 evinrude?
  8. E

    Hard starting 225

    My 91 evinrude 225 is terrible to start when cold. Today I had primed it pushed the key in and turned the engine over and no start for several minutes. Then I shot a little dab of engine starter into the intake and it fired immediately and ran great all day. Any suggestion what may be doing...
  9. E

    Aluminum vs. Stainless

    I heard somewhere that a stainless prop's heavier weight puts more strain on the gearcase than the lighter aluminum. Any truth to this?
  10. E

    Aluminum vs. Stainless

    I heard somewhere that a stainless prop's heavier weight puts more strain on the gearcase than the lighter aluminum. Any truth to this?
  11. E

    oil leaking

    My 91 evinrude 225 has oil on the inside of the cover that goes over the carbs, vro is disconnected running 50:1. I was wondering if one or more of the carbs was spitting? Any help would be appreciated.
  12. E

    Idle timing

    My 91 evinrude 225 manual states idle should be <br />6atdc but after sync and link and all adjustments it still runs high about 1000rpm. I wanted to know if anyone ran this motor at a diffrent setting and if any adverse effects could come of this?
  13. E

    Carb kits

    Anyone know the part numbers for a 91 evinrude <br />e225pxeic carb kit?
  14. E

    throtlle cable

    Anybody know the best way to set throttle cable on a 1991 evinrude 225? I having a hell of a time with the clymer manual. Engine Idle is a bit rough and was told this could be the culprit.
  15. E

    Evinrude 225 plugs

    Was wondering if it makes a diffrence in idle quality whether you use the conventional plug or the gapless plug like the QL16v on my 91 evinrude 225. Also would like to know if any special tools are needed to overhaul the carbs?
  16. E

    Water pressure relief valve

    Does the 91 evinrude 225 have a water pressure relief valve? If so where is it located?
  17. E

    temperature diffrence

    just replaced water pump and had heads pulled and water jackets scrubbed out on my 91 225 evinrude. The motor did not have thermostats when I got it so I put some in it. It was originally running at 175 degrees at wot. Now runs about 130 or so. When I came back and was flushing it found out the...
  18. E

    Removed heads

    Powerhead was running hot on one side of my 1991 225 evinrude. took off the head on that side and found complete blockage on top water jacket. While I was in there looked at cylinders and they are smooth combustion chambers clean as well. just a little bit of carbon covering the piston top...
  19. E

    dhadley help!

    My e225pxeic has head 333809-4 on it. I have checked and double checked with some people on the board and it says it takes head 397860 is it safe to interchange the two sets? use one or the other? I been told your the one to ask about this.
  20. E

    225 heads

    I have 2 questions. Is it possible for one head to run hotter than the other due to a salt buildup on that side? Does anyone know the part number for the heads that came on a 1991 evinrude 225pxeic? was there more than one head for this particular year?
Top