Search results

  1. S

    2011 E-tec Evinrude 15hp

    I bought this used last year complete with controls and harnesses. I have a few questions regarding 2 wires which the previous owner cut off because they were grouped with some other wires, a four pole connector an a single red wire. I believe the single red wire probably goes to the fuse...
  2. S

    2011 15hp HO Evenrude Remote Wiring Harness

    I recently purchased a 2011 15hp HO Evinrude to replace my 1984 9.9 Johnson from a private owner. Pictures 1 & 2 are of a 4 pin connector on the ignition switch end of the remote wiring harness. Can anyone tell me what it is supposed to connect to or if it's not needed to run this outboard...
  3. S

    1999 175hp Evinrude

    I've been in the process of using up a good portion of the 83 gallons of fuel that's on board my boat to get better information as to how the boat preforms with a lighter load. The 53 gallon tank is getting close to being emptied. Will I have any issues trying to start the engine other than...
  4. S

    Prop Questions for my 1999 175hp Evinrude

    We purchased a 1997 Crestliner 2360 Eagle SST with a 1999 175hp Evinrude last April. Currently at W.O.T. I can achieve 39 mph at about 5250 rpm (choppy water). Spec on this motor is 5300 to 5800 rpm. Current prop is a 3 blade aluminum 15 x 17. This boat empty weighs in at 2300lbs. Speed and...
  5. S

    Aerator Timers

    I have to get a new aerator timer for my livewells. The one which is curretly in the boat is a RANGER 3 WIRE AERATOR LIVEWELL TIMER. Initially I found what I was looking for on Ebay at Great Lakes Skipper, but it is sold and haven't found one anywhere else. What I need is some information...
  6. S

    Accumix failure

    I was looking at some of the older posts regarding Accumix. We purchased a used Crestliner 2360 Eagle with a 1999 175hp Evinrude and a 1986 9.9hp Johnson for trolling. Couldn't get gas to the engine and found out that the Accumix tank was the problem. I abandoned the Accumix and went to a...
  7. S

    1999 175hp Evinrude Loses Prime

    Hi everyone. I've used "iboats forum" before and have received excellent info so here I am again. Last April we purchased a Crestliner 2360 Eagle SSt with a 1999 175hp Evinrude. Runs great. I think I have a problem with the fuel system, but I'm not entirely sure. The engine is direct...
  8. S

    1986 Johnson 9.9 with remote oil and fuel mixing tank

    I purchased a used Crestliner 2360 Eagle SST this past April with a 1986 Johnson 9.9 kicker. Motor ran fine with a 6 gallon tank, but won't run off the boats tanks. I found the problem to be with the remote oil tank. This remote oil tank mixes the gas and oil together as fuel passes through...
  9. S

    Evinrude 175 hp outboards

    I'm going to go look at two Crestliner 2360 Eagle SST's, 1997 and 1995 this coming Friday (8/10). Based on the model numbers that were furnished to me, one appears to be a 1999 Evinrude (mod#: E175FPLEEC) and has Fitch on the hood/cowl. I haven't heard a lot of good about the Fitch engines in...
  10. S

    Yamaha 2 stroke oil systems

    Looking at a couple of boats powered by Yamaha 70hp and 90hp outboards (2 stroke). I know that the 90hp's are 1990 model year. After receiving information and opinions on VRO systems, I was wondering if Yamaha had the same/similar issues with the oil system, how dependable they are, and what to...
  11. S

    2 stroke oil systems

    I've been looking at buying a larger boat. Requirements are outboard powered, cuddy cabin, deep V aluminum hull, and preferably 22ft to 24ft. Models I'm considering are Starcraft?s Islander and Crestliner Sabre. I looked at Sylvan Offshore models, but dont' like many things I've seen. I...
  12. S

    Evinrude Power Tilt & Trim

    Re: Evinrude Power Tilt & Trim I managed to get a set of thrust pads at no charge. I checked several model years and came up with the same part number from 1983 through 1990 ( if memory serves me correctly). The only thing I can't be certain of is if any models were omited from the...
  13. S

    Evinrude Power Tilt & Trim

    Re: Evinrude Power Tilt & Trim I don't have the harness, but had already figured I'd need 2 relays in order the keep heat down in the tilt/trim circuit. I purchased 2 - 40 amp relays with connectors (5 blade/pin). I have two wiring diagrams. Hopefully they came through as attachments...
  14. S

    Evinrude Power Tilt & Trim

    Hi Everyone, I'm new to this forum and have some questions about adding a power tilt and trim to my 1979 70hp Evinrude. Anyway, I've already purchased a used power tilt and trim unit. It has 2 wires coming from the motor, 1 blue and 1 green. So far, it appears that polarity is reversed to...
View older results
Top