Search results

  1. marauder11

    1974 Larson Shark

    Re: 1974 Larson Shark Ok here is the exact area as my first picture. I pulled the foam after trying to clean it up with the sanding wheel and it was moving. It was just used to level out the two dips you see there. Next question my thru hull fitting is leaking. Can i just re-silicone that or is...
  2. marauder11

    1974 Larson Shark

    Ok i made a post earlier about wanting to redo my deck on my boat. I pulled the carpet from under the dash and found the issue. Near where the hull comes up close to the floor there is foam poured on both sides. The floor is solid and the foam was glassed to the deck. The two ridges that are...
  3. marauder11

    1974 Larson Shrk

    Ok season overand i want to redo my deck. It has no soft spots. I just noticed that between the two stringers the deck has sloped. Not a lot of slop but if i put my level across it is about an 1/8 of an inch. So can i do this without taking the cap off. Can i do it on the roller trailer. I have...
  4. marauder11

    Rpm

    Ok first question i have a 120 hp 1986 outboard. I have a 17 pitch prop on it what is the rpms i should be getting at wide open throttle. I got it up to about 35 mph. I know that speed depends on boat passanger ect. My RPM gauge was all over the place up to like 5.5k down o 1k . With my old 19...
  5. marauder11

    What do you think

    Kijiji medicine Hat Ad ID 394335938 . Please look at this boat and give me your thoughts. Hours kinda worry me not sure what to think.
  6. marauder11

    Boat construction

    Who makes a good boat. I am looking at upgrading to a open bow run about. Are there makers out there that use all composite materials ect. Thinking brand new or fairly new take care of it and keep it for the long term.
  7. marauder11

    Adding on to a ski pylon

    My brother has become addicted to wake boarding. I have a 15.5 foot Larson Tri hull with a 120 HP Johnson outboard. This last weekend i took him and his buddy to the lake . Both had never gotten up on the board well we had success with both and now the addiction. I have a ski pylon with two...
  8. marauder11

    Exhaust port

    Wondering if someone can help me with the way my motor works. I have a 120 hp 1986 motor. I noticed today that there is water coming out of the top exhaust ports. This is at idle as i am driving and can not see when full out. Why is this?
  9. marauder11

    Starting a 1986 120 hp johnson

    Ok newbie here can someone tell me the proper way of starting your outboard. I know that i have an electric primer or choke when you push the key in. It has taken along time to get my motor started the last two times. After that it start like a dream. Thanks in advance.
  10. marauder11

    Timing

    Ok i admidt i do not know everything. i had boat out last night and needed to adjust idle a bit. I adjusted the timing screw by mistake( please feel free to insert idiot card here). Anywaqy i left the backup nut in the same spot or as close to it as i could. After i relized my mistake i put it...
  11. marauder11

    Mixing oil and gas

    Have just gotten a new boat and am wondering if i can fill my tank and then add 2 stroke oil after i see the amount of fuel it takes. Will it mix ok . I know it might sound stupid but just wondering the best way to achieve the best mix.
  12. marauder11

    Tilt & Trim

    Any type of relief valve or anything to protect motor transom if the lower leg hits say the drive way or bottom. I have an 1986 120 johnson.
  13. marauder11

    1986 120 lower gear case re seal

    Is 4 hours an ok time for a mechanic to redo the lower gear case seals and put in a new impellar.
  14. marauder11

    1986 carb issues

    Ok have motor at shop. I have some carb issues. The mechanic was having issues with motor and rpms blablabla. Well turns out the siphon yube that goes into the bowl and sprays the fuel into the carb is broken or disintegrated . On all four not sure what caused this motor is new to me and that...
  15. marauder11

    Transom

    Hey doing the slow look over of my boat i just bought. Did all transoms come fibeglassed in form factory. I noticed mine is tabbed in but not totally cover in fiberglass. I got a 1974 Larson Shark.
  16. marauder11

    Vro

    Ok keep it or remove it just want your vote.
  17. marauder11

    Paint

    Ok i have bought some paint thru my local boat shop. It is not anti fouling because as he said we do not need to worry about that stuff around here. It is made by the same company as the antifouling is and is white. I am using it to cover over my small scratch and gouge repairs on the bottom of...
  18. marauder11

    Anyone have a old original boat

    Just wondering with all these restorations on here does anyone have an all original boat still.
  19. marauder11

    Gear oil on the floor

    Had motor winterized and now i have gear oil on my floor after i lowed tilt down for the winter. Could this be oil that ran out the top hole and down into the outside prop area. it is not alot maybe a coupel oz.
  20. marauder11

    A step by step how to

    Is there a post on here that walk you through the process of fiberglassing. I see lots with actual boat projects happening that talks about glassing. I am looking for a intructional post more than a project post.
Top