Search results

  1. phoenixgold2100

    johnson overheat issue.

    I have a 99 johnson 150 jl150plees that is overheating. I have an alarm going off and I have installed temp gauges and they are both going past 220 I shut it off at 200 I also installed new temp sensors and t stats. At idle I have minimal water pressure when I hit the throttle it will jump to...
  2. phoenixgold2100

    Is this slow mode or fouled plugs?

    Re: Is this slow mode or fouled plugs? ya all wet and all brown i'll take a pic... see all the brown sauce on the plug washer in the one pic? I soaked the plugs in seafoam deep creep for carbon build up and sprayed that into the cylinders and started it up. it smokes pretty bad with the rpms...
  3. phoenixgold2100

    Is this slow mode or fouled plugs?

    Johnson 150 jl150PLEES. 99. Can anyone tell me if this is slow mode or fouled plugs? I sprayed deep creep into the cylinders and soaked the plugs in it for a bit. I blew it all out with the compressor but did i foul the plugs? I pulled them out and they are wet with brown stuff... I don't...
  4. phoenixgold2100

    synthetic 2 stroke oil.

    I have a 99 johnson 150 and I mix the fuel at 50:1 my question is I have a few bottles of this bel-ray 2 stroke synthetic oil that I mixed for a bike I used to have i am thinking about using this in my outboard fuel is this a good idea? This is high anti wear and says for all 2 stroke...
  5. phoenixgold2100

    Johnson 150 trim noise video included

    johnson 150 99 j150plees. Drained the trim fluid and refilled ever since then I get this noise. Does anyone know what I should do. This noise is not the bushings and doesn't do it all the time as you can hear when I move it down it doesn't make the noise.. I have drained all the air out of it...
  6. phoenixgold2100

    trim tilt fluid johnson 150

    Re: trim tilt fluid johnson 150 no problems with it i just wanted to make sure there was enough fluid in it when i took the cap off it came pouring out. I tried to re fill it and the engine goes up and down but it makes a horrible noise now when i stop it going down and start it again. Here's...
  7. phoenixgold2100

    trim tilt fluid johnson 150

    I just pulled off the cap for the trim tilt resivoir engine all the way up and it comes shooting out. I have read it is supposed to be at level with the hole is this right for the engine? or should it be filled as much as possible?
  8. phoenixgold2100

    johnson 150 water pressure

    What should my water pressure be at idle? I removed the thermostats should I have water pressure with them removed? I don't plan on running it without the thermo's I just wanted to make sure water was being pumped. There was a little coming out the tell tale but no pressure. thanks.
  9. phoenixgold2100

    temp gauge

    Does anyone know if temp sender 174675 - 172843 works with a faria temp gauge? I have already ordered the gauges and haven't ordered the temp senders yet. I think the gauges are standard us 33-240 ohms. Is that what these senders put out? I can't see them being strictly omc guage compatable. I...
  10. phoenixgold2100

    johnson temp sending unit omc part number found!

    Part #:OMC174675 1988-2000 outboards. temp sending unit if anyone is having trouble finding one here is the part number.. Not sure if sierra has a cross reference.
  11. phoenixgold2100

    outboard temp sender

    Does this temp sender go in a johnson 150? thanks guys
  12. phoenixgold2100

    1995 johnson 150 temp sender thread size.

    I am looking to install a temp sender. Just wondering what one fits in my head. the gauge is a faria so i need to know what one works for the gauge as well. Ive seen 1/8 thread and 1/4 threads. part numbers would help. thanks Would this sender work? #TS1029 240 - 33.5 ohm RANGE...
  13. phoenixgold2100

    12/24 volt motorguide. how to wire for just 24v

    I have a motor guide trolling motor 12/24 i would like to wire it for 24 only. I do not have a 3 wire plug it has what looks like a marinco 12/24 recepticle with 4 6 gauge wires going to it. two red two black. I have read I do not need 4 wires to run 24 volt so is it just a matter of...
  14. phoenixgold2100

    Prop to pad height johnson 150

    Hey guys I have a 99 stratos 273 vindicator 17'3 6" jack plate and a 3blade 24 raker prop johnson 150 I am trying to get some info on prop to pad height and what prop i should run. I think the prop is 4.5" from pad at the moment. I'm not concerned with holeshot performance i want as much top...
  15. phoenixgold2100

    Prop and pad to prop height

    Hey guys I have a 99 stratos 273 vindicator 17'3 6" jack plate and a 3blade 24 raker prop johnson 150 I am trying to get some info on prop to pad height and what prop i should run. I think the prop is 4.5" from pad at the moment. I'm not concerned with holeshot performance i want as much top...
  16. phoenixgold2100

    1995 johnson rectifier

    Can anyone tell me how to test my rectifier I have hooked an ohm meter to it and tested every lead reversed the probes and the only one i get a reading from is the gray tach wire. this mean it's a bad rectifier 585219 95 johnson 150 also would i add atf to my trim ? thanks guys first boat and...
  17. phoenixgold2100

    testing rectifier johnson 150

    I have read online when testing the rectifier if you connect ohm meter to ground and touch the rectifier leads you should only get a reading one way...my problem is I only seem to get a reading of 10.2 from the gray tach wire. I touch the leads to the yellow plug either side, and nothing happens...
  18. phoenixgold2100

    overheat sensors johnson 150

    I am getting constant alarm when key is turned on I have checked voltage on the over heat wire and I am getting 11 volts from it and when i hook up a test light to it Purple and tan the test light comes on so i have a ground in the tan wire I guess my question here is is there anyway to check to...
  19. phoenixgold2100

    BOB JOHNSON Wiring issues! again!!!!!!

    I have a 99 johnson 150 and the alarm goes on when the key is turned on and will not shut off (engine not running) so I know it's not an over heat issue. I disconnected the tan wire from the alarm and it kills alarm but when key is first turned the alarm has a dying chirp sound coming from it...
  20. phoenixgold2100

    engine years

    Re: engine years I have a system check gauge seperate from the tach. this is the plug that goes to the check gauge. the wires have been cut and do not run to the engine. . should the 95 harness have these same colour wires from the engine? I am not sure why they have been pulled from the boat...
Top