Search results

  1. alldodge

    Bravo 3 Refresh Questions

    That's normal for a B3, it has 3 gears messing down there and not smooth like the B1
  2. alldodge

    2002 Four Winns 240 instrument problems

    When asking a question it's always best to let folks know just what your talking about. What motor and what depth gauge It's normal for time to cause trim gauge to stop working on all boats. In most cases it's the puck on the starboard gimbal ring. As for the depth finder, most likely same thing
  3. alldodge

    1996 5.7LX EFI TBI Timing procedure

    Scratch the previous, I was hung up on EST There are 2 ways to put motor in base timing mode. Do it with your scanner or place a jumper in the DLC connector. In base timing mode adjust rpm to 1200 if ECM doesn't automatically change. Set timing, return to idle and remove jumper or use scanner to
  4. alldodge

    1996 5.7LX EFI TBI Timing procedure

    Scratch that you side TBI
  5. alldodge

    Outside lower unit will not go up

    Good then you should have 2 relays and your wiring should be as in pic
  6. alldodge

    1st Boat

    Welcome If boat hulls are solid, then it comes down to which motor is in best shape
  7. alldodge

    tilt/trim

    You replaced the puck on starboard side and with wires connected it does not work. Connecting gauge direct to puck it does work There is a bad connection somewhere or your install method has an issue. I connect wires to puck, turn key ON, go back to puck and slowly rotate it until I get a...
  8. alldodge

    tilt/trim

    Sounds like there is a bad connection. The Brn/Wht goes thru the 10 pin engine harness. You could run a jumper from the puck to the gauge to verify there is a bad connection
  9. alldodge

    Outside lower unit will not go up

    Being a 1979 do you have the 3 button up/down/trailer?
  10. alldodge

    Volvo Penta 3.0 Beeping and Ggoing Into Limp Mode

    The sensor is telling the ECM it's overheating. Don't see it being the sensor because it was replaced and same problem. That leaves the connections between sensor and ECM or it's the ECM
  11. alldodge

    Bone headed move - put the plug in with 3M 4200

    Supertech Marine (blue) and Mult-duty (red)
  12. alldodge

    Outside lower unit will not go up

    Most likely the trim limit switch is the issue. Can you get drive to come up using the trailer buttons?
  13. alldodge

    Rebuild old mechanical Fuel pump or go for Electric Fuel pump

    Many do change to electric and is simple enough to do. Let us know and we can supply the how-to
  14. alldodge

    Trim cylinder hose replacement

    With cylinders off, run pump dry Can try to clean tank out and refill or add more and run pump again to flush out
  15. alldodge

    Rebuild old mechanical Fuel pump or go for Electric Fuel pump

    Welcome If the carb is getting fuel then it will not just die quickly, takes a while. Tell us more about your symptoms ?
  16. alldodge

    Hurricane Helene

    NC Orgs
  17. alldodge

    Outside lower unit will not go up

    Welcome What motor Merc, VP other?
  18. alldodge

    Which trailer w/o a boat to sell?

    Need 2 people Take the ball hitch off the truck and connect to trailer. Jack up the wheel on trailer. One step down on hitch and see if brakes are applied
  19. alldodge

    tilt/trim

    Welcome Might try to use the return key once in a while to make it easier for us old guys to read The gauge needs 3 connections to work. 12V to power it (comes from key, purple wire) Ground Black wire Sender Brown/White wire coming from puck Puck 2 wires, one goes to ground and the other...
  20. alldodge

    Hurricane Helene

    Whole lots of folks hurting Read part if I-40 is closed due to land slide
Top