Search results

  1. alldodge

    mercruser 888 wont rev past 2000 when in gear in the water

    So it was actually a 17P? If it was a 3B-17P, using a 4B-19P is the same as a 3B-21P This brings up another question for clarification. Your original motor did have same firing order as the new cam? Both were and still are 15426378 correct
  2. alldodge

    2002 5,7 Mercruiser exhaust manifold keeps cracking - 5 times this summer

    Seeing some air is ok so long as it's not constant bubbles, which I don't see. Cooling system IMO is ok. Only thing left is the fuel and that doesn't make any since with compression being good all around. Sorry if this was answered already, but does spark plug number 5 look the same on both motors?
  3. alldodge

    1985 mercruiser 3.0 starter

    Search for marine pmgr starter Then look for ones with straight across bolt pattern, like this ONE
  4. alldodge

    mercruser 888 wont rev past 2000 when in gear in the water

    Assuming same drive What prop was on the drive prior to rebuild?
  5. alldodge

    1985 mercruiser 3.0 starter

    Thanks, number above is correct
  6. alldodge

    4.3gl dieseling

    No
  7. alldodge

    1985 mercruiser 3.0 starter

    Going to need a serial number of your motor because you should have a solenoid attached
  8. alldodge

    1985 mercruiser 3.0 starter

    Starter with straight across bolt pattern is 8M0090697
  9. alldodge

    1971 Glastron GT160 Rear Drain Hole Question

    Welcome That's the splash well drain. All outboard boats have them
  10. alldodge

    Merc Smart Craft // 150 Four Stroke - Question

    Muc is better, but my thought is don't put a lot into the readings. All readings are from electrical (non-calibrated) sensors. If they are a bit off from one another, that is just differences in sensors. I have 2 new 250 Verado's and the starboard sensors show more fuel, higher temps, and lower...
  11. alldodge

    Closed cooling through hull valve placement

    I think the clear hose will show bubbles and if so then it will be in the pump area most likely
  12. alldodge

    Closed cooling through hull valve placement

    ok Alpha drive, and 2007 should be G2 When impeller was replaced what did the housing look like? Was there any markings. Wonder if the housing was sealed so it doesn't leak Could put a short piece of clear hose where the drive hose connects to heat exchanger. When boat is running look for bubbles
  13. alldodge

    Closed cooling through hull valve placement

    I can move it, is it a Merc, VP, other?
  14. alldodge

    Closed cooling through hull valve placement

    Your question has nothing to do with the boat, it has to do with what motor you have
  15. alldodge

    I/O (Sterndrive) Conversion to Outboards

    Hey Ted go look at formula forum, guy could use some inside wife Lifpo4
  16. alldodge

    Glastron soft floor

    Thanks, all good West marine "they are unsure" Your test show issues Me, before E10 even came about I had a small fiberglass tub and put gas in it to clean some parts. The next day it ate right thru and dissolved the bottom Florida marine and tank coats outside of there tanks with epoxy (cost...
  17. alldodge

    Glastron soft floor

    Evidence please
  18. alldodge

    Glastron soft floor

    Resin will add strength to the walls but wouldn't keep it from leaking, need epoxy for that. Gas gets in contact with poly resin it just dissolves it. New aluminum tanks recommend epoxy paint coating on outside.
  19. alldodge

    4.3gl dieseling

    Don't know which GL you have A, B, C ...E
  20. alldodge

    Glastron soft floor

    I wouldn't do that unless your very careful. No more the about 3 psi using a bicycle pump. Getting much above that turns a tank into a bomb If tank comes out and you don't see pitting in the inside or outside IMO your good
Top